drive

Have three for some reason. $20 each, or $50 for all three $11 USPS small flat rate shipping.

Hi, On offer is SST09530-35010, differential pinion depth adjusting gauge. The link to another mud members post explains how the tool is used very well. https://forum.ih8mud.com/threads/sst-09530-35010-differential-drive-pinion-adjust-gauge.1009796/ I am asking $475 and an air filter housing...

Leaves are starting out in the mountains of Virginia. Hope you get a chance to get outside this weekend. Let’s see some pics!

HI All, I have had my 85' FJ60 for about 8-9 years now. Body/chassis has 212k miles. Engine has close to 160k miles from donor 84' truck paired with a rebuilt t-case with an advanced adapters 4:1 low gear set and a new h55f transmission. I have developed an odd jingle noise while under load...

Fresh from JP! I don’t care what the haters say, I’m stoked about the 250/550! 2024 Lexus GX Prototype Off-Road Drive: It Wheels as Good as It Looks - https://www.thedrive.com/car-reviews/2024-lexus-gx-prototype-off-road-drive-review-specs-impressions

I have vibration that gets pretty noticeable around 60mph. It feels like it is in the back. Steering is solid and no vibs in steering wheel. Had this before I put new tires on and balanced. I checked the drive shaft and found about twenty thousands run out on the barrel and the yoke is so...

Went to Flagpole Knob, VA, then did some of the backside - had to turn around because I don’t have rock sliders yet. Then we took the paved road to reddish knob to the lookout at 4400ft elevation. Had the Shenandoah valley on one side and the rolling hills of West Virginia on the other side.

For additional info, I did skim through these two threads below. How I grease my front driveshaf Drive train lubrication My questions are: Do I have to get all four wheels off the ground at once when greasing all the zerks? Or, can I jack either the two wheels of front or rear separately...

Pro Tip of the day - When measuring your drive shaft length for purposes of ordering a better one from Tom Woods, measure twice, maybe even three times. Use your best penmanship and make sure you can read your own damn notes. Then before pressing send on your order; go ahead crawl back under...

So I finally decided to pull the trigger and get a Tatton DC forward drive shaft for my LX450. I went with CJ Tatton given I heard great things about the quality of his work. When I tried to install and connect the CV to the T-case it would not slide into place. The CV’s circular holes would...

Hello to my fellow 200 Series Land Cruiser owners. This is my first posting and I need help and some guidance. My wife drives a 2017 LC with 24,000 miles and in pristine condition. We bought it new and recently paid it off....love it. I am attempting to perform as much maintenance on it as...

Any PCM gurus out there? No vacuum leaks, 650 smooth idle, no VSS, no stalling on decel. Relentless P0507 "Idle speed higher than expected." Will the absence of a VSS to the PCM cause the P0507 code? Seems to me it's plausible. PCM assumes idle speed off throttle but drive train pulls RPMs...

For those of us running custom front driveshafts the OEM studs are just barely long enough to get full nut thread engagement even with leaving out the washer. Anyone have a P/N and supplier for a 10mm longer studs that fits?

Surprised this hasn't made it into this august section of the 'mud! Context - Darwin is the capital of the Northern Territory, and renowned as a bit of a frontier town here in Oz. Way back in 1983, a bunch of blokes, most likely having had too much beer and with too much time, decided to...

Taking a 10hr drive. Any accessories that would help to make things more comfortable/convenient? Already purchased the BH3D cup holders and air vent phone mount holder. Maybe a seat cushion? Any ideas would be appreciated!

hi mud, I could use some advice. 07 LX470, 190k. I've had the truck for 3 years and 20k miles. No major issues until a few weeks ago. Was driving over a mountain pass and noticed that when I accelerated, there was a high pitched whistle from engine bay. Letting off the gas slightly caused the...

As the title says... clean, bone stock sub- 175k mile left hand drive '95 HDJ81 with a manual and factory lockers, no body rust, minimal undercarriage rust (nothing rust converter can't cure), no leaks, no grinds, no unusual noises, and a clean interior without any cracks in the plastic or...

Have a Trail Gear chromoly flange kit, $70 Paypal friends n family, plus shipping or local pick up.

Compression numbers are 80lbs +/_ 2lbs in every cylinder. Does not burn oil and the spark plugs look good. Runs good but sometimes I think it is tired as I often times have to put it in 4low to get it to move on a steep hill when out playing. It seems like it would probably be reasonable to do...

I have read countless threads and still can't figure out how to fix my problem. 1994 land cruiser when put into drive, won't down shift to first, just try's to start out in drive, I can manually shift to 1st then 2nd then 3rd and it works great, and then mashing on the throttle it won't down...