diesel

New TIMING BELT FRONT END BRAKES ALL COMPONENTS SERVICES WITH AMSOIL RUST FREE SOFT TOP 25K (TWO 4 0) FIVE two 6-o44 eight

The 14B-T is maybe my favourite B engine and during much internet trawling, I finally came up with some official-looking specs. It comes from a Taiwanese customs website, looks to be an official document for import/registration in Taiwan. The 14B-T was mostly sold in Japan in 24V Dyna/Toyoace...

Hey Folks, I'm researching my next build and I'm planning on a 2.8 Durax that is tuned to 220hp / 440tq. With that level of torque, I seem to not be able to find any specs on max torque of land cruise transfer cases. I was think of going with a FJ62 case converted to FJ60 shifters. What do...

Hello everyone My 1hz does not start or starts weak when it is hot.But it starts rapidly when it is cold. Fuel system (timing), the battery or what?

Came off a B-series engine, I think 3B but can’t remember exactly. No idea on compatiblility. $20 plus shipping. Can vapor hone it and make it beautiful for $20 additional

Got me a running engine for my truck ... but the block is pretty crusty ... just wanted to make sure before going too far on the rebuild that there is no oil gallery on the exhaust side of the block where circled , picture is not mine

I have 3 sets of the oem floor mat sets available for lhd 76 models , in my logic these will certainly also fit the older LJ and KZJ 77,78,79 lhd models and the front ones will fit any lhd 7x model 150$ including shipping in the lower 48 , these are the only ones I have so once these are gone...

As detailed in another thread, I am likely going to be rebuilding my 2.8 diesel. Because the 3L and 5L engines (5L with mech injection) are incredibly similar, I have considering swapping in a low mileage 5L. Finding one has so far proved difficult. I don't know of anyone that imports them...

On a journey to diesel swap my 40, and am looking hard at the 15b-FT/FTEs. I have a potential source for an FTE, and originally thought one could just swap a mechanical IP from an FT and toss the electronics. However, I then came across that 1HD-FTEs cannot be easily converted to mechanical due...

Hi all, greetings from the Pacific Northwest. I'm excited to join the 100 Series family. Any other JDM 100 series folks out there? Right hand drive rocks! ;-) My LC is pretty much stock, 88k miles, and is in stunning condition. (I can't take credit; the former owner in ***uoka, Japan took good...

Looking for a 1HD-FT/Auto Trans ECU w/ no EGR (part number 89551-60031).

Good evening all I’m completely stumped here. On my HZJ76, which I’ve had basically since “new” (full story here: Ali, the 2008 HZJ76 - https://forum.ih8mud.com/threads/ali-the-2008-hzj76.1272844/), quite suddenly I’m experiencing severe smoking and hesitation. The engine has 16,000km on the...

Looking for a diesel shop in CO that can tune/time the fuel pump in an HDJ81 after a rebuild of fuel pump.

I have for sale 2 complete diesel gauge clusters for diesel trucks and one single 1FZ tach (removed when I did the diesel conversion). Prices and descriptions below. 1. 80-series Manual Diesel Cluster Asking $250 plus shipping from Cincinnati, OH 2. 80-series Auto Diesel Cluster - Sold...

Trying to restore my factory superglow system, I am unsure of the pinout for the superglow timer.

So I'll start this off with a photo. Motor sludged up horribly. Worst I've seen. I haven't had the valve covers off this truck since I bought it, but last oil change was approx 3500 miles ago. Only about 120,000 km on the odometer. Anyway it began making noise this weekend promoting me to...

Can any body tell me what 5 speed gear box will bolt up to a landcruiser 2H diesel engine.

I bought my hzj77 three years ago almost to the day. Ever since day one it's had a noise that I haven't been able to *nail* down. (foreshadowing perhaps?) Its most noticeable in the morning when cold and you accelerate to about 2200rpm. Sometimes I can hear it subtly through the rev range...

Looking for the non AC type of tensioner bracket for a 12ht. Pic below for reference

Considering selling my fj40 om606 swap project, I started piecing this together while everything was shut for Covid and got all the main pieces together and then things got back to normal and I haven’t had time to finish it. It is a mix of a 70 and 68 fj40 body parts with a later 4 speed...