Replaced the master / slave cylinders on my 72' 40 today. The job was partly replacing old / worn parts and part trying to put the right parts in the right places after PO had rigged some things (think hose clamps, etc. ugh).
Elder Statesman hooked me up with the cylinders, brackets, etc...
Need advice from the experts. The last couple of times I've started my '75 40 after sitting for a week, I've had trouble shifting into reverse. It feels like the clutch hasn't disengaged reverse gear which feels like it's turning. A couple of times, I've also had trouble shifting into 1st or...
Hi guys
As some have already seen in a previous post, i am going to buy a V8 2023 Model V8 Troopy (VDJ78)...
So the vehicle is ordered and should arrive in January....
Since i am using it for towing and offroad traveling i will do a custom dyno tune (expecting maybe 250-300hp at the flywheel)...
Just on the odd chance does anyone here know what torque setting I should be using on a flywheel that came out of a 2023 vdj79 series or if loctite should be applied I am fitting it to hzj80 model. Thanks in advance
I own an 86 HJ60 CDN with a 12HT swap.
My clutch pedal started to feel real spongy yesterday, only really engaging at bottom end of stroke and literally nothing at the top. So I did the usual check on fluid in the master cylinder and if there are any leaks inside and out. Also checked slave...
I’m looking for an AC clutch for my 1994 Prado with a one KZTE or I would take a whole compressor with a new clutch preferred just a clutch anybody have any ideas on where to source one of these? I’ve heard rumors there are some US domestic versions that will work from a forerunner, thanks Knute
I have most of the parts necessary for a H152 transmission swap for sale. Many of them are New Old Stock (NOS)/New in Box. I have listed the parts below and have corresponding photographs. This transmission could be put in an 70 series, 80 series, 100 series gas or diesel.
I'm asking $8,250 or...
Hey guys, the clutch was on its last leg and I decided it was time to change it out. The oil pan gasket was leaking and figured we might as well replace the gasket. This was sitting in the oil pan, any ideas what this is???
I have '75 with SBC and a stock Chevy low profile clutch setup. For the most part, it's worked just fine in normal driving over the last 20K Miles.
This year, I've started to do a bit more serious off-roading on steep slick rock (Moab, Farmington NM). I have an issue if I'm trying to...
Hi gang. Just want to say a quick apology to anyone that has answered on my previous posts. Life suddenly got in the way this year and kept me from the tank, but I'll be back in the game next month and will follow up on every post I started. I definitely appreciate all your help.
As I'm getting...
Over this past week I went out to see the Annular eclipse, while I was doing this the clutch pedal went out and would not engage the clutch. I checked and where the clutch master cylinder goes into the firewall it was sopping wet with fluid. My question is what exactly do I need to do to...
Was going to replace the clutch master cylinder on my '83 FJ60, and got about 3 minutes into it before getting stuck. The clutch pedal pin won't come out of the pedal. It's not rusted, it's not frozen, everything very clean, I can actually turn it in place with almost no resistance. But, it...
Has anyone ever redrilled a 1HZ (275mm) flywheel to accept a 300mm clutch cover?
Why would I bother? Because the 275mm flywheels are sorta worthless… and the 300mm flywheels are $700-800.
Just got an FJ60 and clutch no longer gives pressure when pressed down. Went down to check out the clutch fluid and the master cylinder was empty. I then followed the line to the slave cylinder (release) and it showed signs of leaking. Attached are photos of the slave cylinder. I tried to bleed...
I have a new build with a new OEM clutch master and secondary cylinders, stainless hard line, and braided flex line. There are no leaks.
I've bled the system a few times following everything I know, plus the Haynes manual, until there there are absolutely no bubbles - just clean fluid. The...
Selling left over parts. All new in boxes.
31250-60401 -> Clutch $200
31210-60162 -> Clutch Cover $225
13405-17020 -> Flywheel $450
CMT-040 -> Master Cyl. $50
Or all for $750