clutch

I have most of the parts necessary for a H152 transmission swap for sale. Many of them are New Old Stock (NOS)/New in Box. I have listed the parts below and have corresponding photographs. This transmission could be put in an 70 series, 80 series, 100 series gas or diesel. I'm asking $8,250 or...

I have a clutch pedal assembly from a 1984 FJ60 Landcruiser. There is some light surface rust, but it works correctly.

Looking for a mounting bracket for the clutch slave cylinder in my 72' 40. I'd attach a photo of one but I'm missing it - hence the ad. :)

Hey guys, the clutch was on its last leg and I decided it was time to change it out. The oil pan gasket was leaking and figured we might as well replace the gasket. This was sitting in the oil pan, any ideas what this is???

Is there someone who can tell me what the circled part in the photo is for? Can it be removed? Does it still work without that part? Thank

I have '75 with SBC and a stock Chevy low profile clutch setup. For the most part, it's worked just fine in normal driving over the last 20K Miles. This year, I've started to do a bit more serious off-roading on steep slick rock (Moab, Farmington NM). I have an issue if I'm trying to...

Hi gang. Just want to say a quick apology to anyone that has answered on my previous posts. Life suddenly got in the way this year and kept me from the tank, but I'll be back in the game next month and will follow up on every post I started. I definitely appreciate all your help. As I'm getting...

Over this past week I went out to see the Annular eclipse, while I was doing this the clutch pedal went out and would not engage the clutch. I checked and where the clutch master cylinder goes into the firewall it was sopping wet with fluid. My question is what exactly do I need to do to...

Was going to replace the clutch master cylinder on my '83 FJ60, and got about 3 minutes into it before getting stuck. The clutch pedal pin won't come out of the pedal. It's not rusted, it's not frozen, everything very clean, I can actually turn it in place with almost no resistance. But, it...

Has anyone ever redrilled a 1HZ (275mm) flywheel to accept a 300mm clutch cover? Why would I bother? Because the 275mm flywheels are sorta worthless… and the 300mm flywheels are $700-800.

Just got an FJ60 and clutch no longer gives pressure when pressed down. Went down to check out the clutch fluid and the master cylinder was empty. I then followed the line to the slave cylinder (release) and it showed signs of leaking. Attached are photos of the slave cylinder. I tried to bleed...

I have a new build with a new OEM clutch master and secondary cylinders, stainless hard line, and braided flex line. There are no leaks. I've bled the system a few times following everything I know, plus the Haynes manual, until there there are absolutely no bubbles - just clean fluid. The...

Selling left over parts. All new in boxes. 31250-60401 -> Clutch $200 31210-60162 -> Clutch Cover $225 13405-17020 -> Flywheel $450 CMT-040 -> Master Cyl. $50 Or all for $750

Finding a crack in my radiator that only appeared under pressure and caused my truck getting hot has lead me down a bit of a rabbit hole. In looking up things related to the cooling system I found that a bunch of the 80 and 100 series guys (especially in hot and humid areas) are opening up their...

My 72 ( never ran in years) has a 350, 4 speed ( early chevy car trans) I have rigged clutch hydraulics, properly bled, with Toyota slave. Clutch stops hard about 1/3 to floor, clutch arm is moving about an inch. Now what? I know oem 40s well, but not US clutch)trans. Ideas? Afraid to...

I am finally finishing up with a 5 year frame off on my 72 FJ40. I swapped to a 4 speed (kept 3 speed xfer) from a 77 with a kit from @marksoffroad. My issue now is the clutch slave cylinder is not returning all way back and the clutch is slipping. I have doubled up the spring to the fork an...

Tried searching but I couldn't find anything recent. Are ac compressor clutches available? If so what's a good part #? Thanks

After some troubleshooting of some very loud squealing when my AC tries to engage, it appears my AC clutch is not longer engaging. My question: do any US models share the same AC clutch assembly? Toyota part number: 88410-60310 1994 HZJ73. 1HZ

Removed these parts from a fj73 I am converting to 1HZ Power steering lines sold Clutch slave plus flex line 50$ plus shipping

I’m gonna bring this topic up again which has been going on for years and Jim Loves it he always gets a kick out of these posts I picked up this clutch kit I stumbled onto with the correct low profile pressure plate that is compatible with the Toyota hydraulics For $65 bucks suppose to be also...