brake

Rebuild front axle less than 1000 miles Includes steering tie rod and drag link and brake lines Rear included . Just bolt in and go $1500

Nevermind - figured it out.

I bought a used OEM spoiler for my LX470 and would like to find female connector for the high mount brake light to make it fit exactly like factory. I know this is waterpoof connector that is also used by toyota for ABS sensors. Can someone help me find the part number for the female connector...

I've been removing some aftermarket antenna stuff (am/fm and uhf cb) from my 80 today and got curious about the vacuum setup that is used with the brake booster (no clutch booster on Oz 80's). I've never seen any sort of warning light show up or any sort of buzzer making a noise, so I'm not...

I have a 77 FJ40 (5.7 swap) I had some smoke from my exhaust and realized it was my brake fluid dripping onto it. Specifically it’s draining the rear reservoir ( yellow circled area, ) coming from the bolt inside. I have never had to work on a master cylinder so I’m not familiar with trouble...

I was working on bleeding my brakes yesterday and noticed that when my daughter was pushing on the brakes that brake fluid was spraying out where the brake line mates to the proportioning valve? Will a bad proportioning valve do that. The flare on the brake line looks ok to me. Any advice would...

What is the valve under the master cylinder?

Just had rotors turned on 2015 @ 30K.......no more vibration, but now pedal drops further. Assume result of less meat on the rotor? Did not change pads 8MM. Brake fluid reservoir about 3/4 full at rest. Any concern? THX

I have a 1970 FJ40, original F engine, most everything is original as far as I know. Aftermarket temperature gauge, normally operates around 180-200 deg F. Once it gets above 200, you can tell the thermostat opens and brings the temp back down. Have had it this way for over 10 years without...

For my 8-‘85 fj60, driver side , left rear brake backing plate. Don’t really need new, but have posted in classifieds & so far nothing. Anyone know of a source? New or used. Thanks.

looked around an couldnt find a straight answer. checked the FAQ's and nothing exact. real basic question, and maybe this will reveal my ignorance, but Ive only owned two cars, 89 isuzu trooper, and 82 troopy, but are all the brake fittings on later model cruisers the same? I ask because I am...

I have a new one for everyone........I recently got another FJ62 and noticed brake lights not working. I replaced brake light switch with new Toyota OEM as I noticed the switch was missing. Plugged right in to original harness with connector and green wires, etc. Now the brake lights are ON...

After 6 months we had a break failure on our 3 door 2022 land cruiser, basically you would pump the brake pedal and nothing would happen, we could see the fluid in the reservoir drop and then the fluid return but it had air in it, a local garage put it on their ramp and saw no signs of leaking...

After 6 months we had a break failure on our 3 door 2022 land cruiser, basically you would pump the brake pedal and nothing would happen, we could see the fluid in the reservoir drop and then the fluid return but it had air in it, a local garage put it on their ramp and saw no signs of leaking...

I'm missing one of the jamb nuts that goes with brake switch. Only have one. Does anyone know off hand what the size/thread is of the the nut?????

Figured since I’m doing this I’d make a thread in the event it would be beneficial to anyone. So far we have done the fronts and I ran hard lines. Going to tackle the rest this weekend. It’s been pretty simple so far! We had to get some flexible hoses that were longer than the ones provided...

In order to use the stock emergency brake on my upgraded 55, is it possible to use the three speed brake assy on a newer FJ40 4spd? fj55 pict note the brake cable is on the passenger side vs a newer 4spd has the cable on driver side pointing in opposite direction.

I purchased a Speedi sleeve from SOR. The included applicator does not seat the sleeve in the correct position. Do I find a way to seat this down all the way or…..? Help me out friends.

I have this on going issue with my parking brakes. I adjusted the parking brake pads at least 4 times but it didn't solve the problem. Finally I even lower the adjustment screw all the way down on both sides. Still whenever I disengage the parking brakes and I am about to drive, the rear wheel...

I was on the highway at about midnight and felt my brakes go to the floor as i was getting off the highway. I could still stop it by going to the floor. I pulled into a parking lot and saw smoke (probably brake fluid that came off the exhaust) and saw that one of my brake lines in the rear went...