axle

Hi guys, I've been lurking for awhile but after much searching, I finally purchased a 1978 FJ40 on the weekend. I've worked in the automotive industry in the past and have collected and restored many classic vehicles but this is my first FJ40 so I've got a steep learning curve. My FJ has Apr...

For the life of me I don't remember what side this backing plate came from but I do know it's from the front axle of a 96 80 series. It's in good shape needs cleanup. Price $20 buyer pays shipping best to email me shmukter@pa.metrocast.net

I dont really have a build thread for my truck or anything, but made this thread so im not just spaming the "what did you do with your 60 this weekend" thread. This will just be stuff for my @TRAIL TAILOR coil conversion done in my garage at my house. Photos, questions, etc. Thought it would be...

Selling front and rear dobinsons 4” flexi coils. They are used, the rears are a little crusty, fronts are starting to chip. $250 pick up

OK I'm ready to sell these parts from the 96 80 series that has been stripped. Locker switch itself works great and has a short section of the wiring harness with it, connector is intact. 4 wheel drive control computer (part #179600-0083) has the connector with it along with a considerable...

I want a solid axle LC for Moab and Colorado trails. My only hangup with the 80 series is the low power climbing the Colorado passes. Engine swaps are expensive and I have no way to do one. Would it be cheaper to SAS a 100 series?

This axle has around 250k and was working perfectly when pulled. I live in Anderson SC and can possibly deliver to the Atlanta or Charlotte areas. Asking $350 but feel free to shoot me an offer or trade idea.

I've got an H55 with 33's in my 1984 FJ60 and running stock 3.73's and would like to replace them with 4.11's. If anyone has a set of 4.11 thirds they want to sell or swap, I would love to buy or trade. If you have a set of locked thirds, that is even better. I'm in Georgia, but willing to...

New warn hubs part # 28771. $200 plus shipping

Does anyone have interest in this front axle either complete or parted out? It’s from my ‘65 45 long bed. It has warn hubs and, I suppose, ball and claw axle assembly. Also the diff is different on these early rigs. I also have the complete rear axle too. I’m willing to disassemble and ship...

I have the springs here that were removed form the 96 80 series truck I have been parting. Not sure how much lift they are but the truck had a very nice look to it. Before disassembling it I measured from the garage floor to the underside of the front fender and the rear wheel opening measured...

Found some contradicting opinions on this. My front drivers’ CV is starting to squeak, so it’s probably already plenty overdue for replacement (no tear in boot). I have a road trip slated for the holidays (CO to TX and back). My budget net of some unforeseen life stuff, a pile of maintenance...

No leaks or issues. Just removed this week. $400 firm local pickup, cash. I drove the car and there were no whines, leaks, bubbles or other problems. Shipping, due to weight is about $70, I will shop for best price but shipping has become outrageous lately. No shipping outside 48 states...

I am pulling my rear axle to remove rust, and to check everything over. One side of the passenger upper link mount is suspect and it would be a good time to reinforce it. Does any sell a reinforcement kit for the upper link mounts? Search came up with stuff for 3rd gen 4Runners. It looks...

Selling a pair of birfields removed from a running 96 80 series. No clicks or noises from the front axle grab a cheap spare or two. Birfs $50 each buy both for $90. Also have the inner axle shafts they look great all splines are nice and straight and the seal surfaces are good. Either side $35...

Hi there! I was quoted $800+ by a shop to fix this rear axle seal leak, I’m new to cruisers and bought my LX 3 months ago and am baselining all maintaince items slowly so I apologize for any ignorance. Is the condition of this severe and urgently needing replacement? Let me know if more pictures...

So I no longer have a 40, but I still have this full-floating rear end with Nitro Chromoly Axles. I will probably be selling this thing locally, but I was wondering if anyone had an idea of the value. Thanks in advance for your input. Edit for additional info: WMS to WMS= 54 3/4", Center of...

I've 'inherited' some OEM LandCruiser suspension parts. I'm told they had 28K on them when they were swapped for an upgrade. I don't have a lot of info aside from the part numbers on the shock absorbers. 48510-60170 48530-60270 The 200 Series that I've listed is my best guess based on looking...

Selling my Diamond solid axle setup for a 100 series. The housing and shafts were purchased through Front Range off road. These are extremely stout housings with 0.375” wall DOM tubing, billet 80 knuckle balls, 0.500” thick diff mounting flange. Parts are for a radius arm setup. This is the...

Which CVJ axle should I get if I have a simple 1" coil over type lift. I have the Bilstein 6112 ride height adjustable coil-over setup in the front. This really is not a lift as all it does is move up the ride height within the stock travel. They have a "No Lift - Stock Angle" option and a...