axle

Front axle alignment tool. Never used. Pics below are the first time I removed the parts out of their original packaging. Don't own any more land cruisers so it's time to pass it along. Looking online, prices are all over the place for this tool - $539 - $285. $300 shipped anywhere in the lower...

I need a pair of steering arms for fj60. Thank you.

I "deleted" the AHC system on my 2001 LX470, and have some good AHC components available for a new home: Pump & Reservoir, with mounting bracket All 3 height sensors 3/4 full jug of AHC juice Torsion Bars Rear Springs Spheres are all broken, and scrapped. Take it all for $100 Located in Bend, OR

Hello, I need an axle and housing cut to length in the SW Washington/ Portland area. Any ideas? Thanks.

Hello, I need an axle and housing cut to length in the SW Washington/ Portland area. Any ideas? Thanks.

Hello, pulled out my rear axles as they were leaking oil a bit. Both axles are having groove in them, the longer axle is very noticable, the short axle is little bit better. One of the spindles got few scratches, not sure if these can cause leaks too. So, the axles can be easily replaced, but...

Crew will be leaving early on 8/3 for Mile High to see Foo Fighers. Then down to Classic Cruisers Sunday and over to Ouray 8/4-8/9. https://forum.ih8mud.com/threads/sas-8-official-page-08-05-2024-08-09-2024.1330181/

Primarily for my full-frontal nerdery. There are a wide variety of spindles used on the 7x Series throughout the range. Most are self-explanatory but it gets a bit weird when you get into the late model stuff that can have ABS or not and/or Dual Mode Auto Locking Hubs (DMALH). Lots of combos...

Rear axle from 1998 Toyota Land Cruiser. E-locker housing but the locker actuator is broken and will need to be replaced. Includes calipers, rotors and pan hard bar. Can ship if you make arrangements with a carrier that is local to me and I just drop it at their yard or they pick up. I have a...

Guys, Need some help, been chasing an oil leak. I thought I had it by replacing the following: -Oil filter housing to block gasket -Fuel pump to block gasket At low speeds (up to 50mph) I have min. oil leak, almost not noticeable. But at fwy speeds, the oil amount that leaks is all over the...

This master cylinder was removed and replaced as preventative maintenance. It functioned just fine when removed. It has 225k miles on it. Price: $400 includes shipping to continental U.S.

1991 FJ80, a while back I had a shop who said they were experienced with Land Cruisers rebuild the front end -- axles, steering knuckles, maybe some other stuff, I don't remember. The axles they used were aftermarket, they have two outboard grooves for a snap ring, I suppose for different...

Hi all. Looking for advice on what to do about the CV Boots I saw leaking on my 2008 4Runner, 132k miles. See photos. Axle with the "CPTD" is passenger side and was replaced by dealership in 2019 when they said the original was leaking. The other/driver side (bottom photo) is original axle...

I’ve searched high, low, left, right and in between. I cannot find anything on the procedure to replace the old brass “seals/bushings“ in the pre 69 front end. I have replacement bushings on hand, the old ball and claw joints are disassembled and I’m ready to install the bushings. Just looking...

I'm sure this has been discussed before but right now I am extremely frustrated on this Christmas Day after installing my third CV axle in 3 months last night only to find out today when I arrived at my family's house for festivities I have checked out the install from last night and discovered...

Used for a few hundred miles on my LX470 but too stiff for my setup. Buyer pays shipping. Only accepting Paypal or cash with local pickup in Tulsa, OK. $100

In need of a right rear axle for my 1972 FJ40. Cut a groove in mine trying to get the inner race off. Thanks

I’m in the process of dismantle it my 93 that got tipped over last spring. I’m getting close to being ready to take body and frame to the scrap yard and figured I’d ask if anyone wants a solid, rust free 80 frame. I’m located in SW WA 25 miles NW of Portland Oregon. $200/offer If...

See description and ebay auction here: https://www.ebay.com/itm/176117875290?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=8s4CvAZiRy6&sssrc=4429486&ssuid=8s4CvAZiRy6&var=&widget_ver=artemis&media=COPY Bought the light / medium duty shocks, drove 300 or so miles on em and realized i should...

What’s the difference? Front axle housing FJ40: 43110-60122 (08/1980 - 04/1986) BJ42: 43110-60094 (08/1980 - 10/1984) Rear axle housing FJ40: 42110-60025 SEMI FLOATING AXLE (08/1980 - 10/1982) BJ42: 42110-60052 SEMI FLOATING AXLE (08/1980 - 10/1982) What could be the difference? Different...