axle

Selling a pair of warn hubs they're complete and have a bunch of extra fasteners and parts with them. Will fit any disc brake equipped FJ40 or 55 and all FJ60 or FJ62 trucks. Price $80 plus the ride. Best to email me shmukter@pa.metrocast.net

Selling the ABS system from my 1994 80 series. When removed, everything was working as it was supposed to. The wiring harness for the front and rear axles are in good shape with no exposed wiring or damage. The harness comes with the brackets that were used to mount to the axles. All four wheel...

Came across this nice clean set of drive flanges they are 30 spline very clean. One dust cap is included. Price $95 postpaid anywhere in the CONUS. Buyers from anywhere else pay actuals shipping cost.

SOLD! Bought from Kurt a few years ago. Comes with Koyo wheel brearings. $180 shipped anywhere in lower 48. PM me with an offer if you are so inclined.

Front axle alignment tool. Never used. Pics below are the first time I removed the parts out of their original packaging. Don't own any more land cruisers so it's time to pass it along. Looking online, prices are all over the place for this tool - $539 - $285. $300 shipped anywhere in the lower...

I need a pair of steering arms for fj60. Thank you.

I "deleted" the AHC system on my 2001 LX470, and have some good AHC components available for a new home: Pump & Reservoir, with mounting bracket All 3 height sensors 3/4 full jug of AHC juice Torsion Bars Rear Springs Spheres are all broken, and scrapped. Take it all for $100 Located in Bend, OR

Hello, I need an axle and housing cut to length in the SW Washington/ Portland area. Any ideas? Thanks.

Hello, I need an axle and housing cut to length in the SW Washington/ Portland area. Any ideas? Thanks.

Hello, pulled out my rear axles as they were leaking oil a bit. Both axles are having groove in them, the longer axle is very noticable, the short axle is little bit better. One of the spindles got few scratches, not sure if these can cause leaks too. So, the axles can be easily replaced, but...

Crew will be leaving early on 8/3 for Mile High to see Foo Fighers. Then down to Classic Cruisers Sunday and over to Ouray 8/4-8/9. https://forum.ih8mud.com/threads/sas-8-official-page-08-05-2024-08-09-2024.1330181/

Primarily for my full-frontal nerdery. There are a wide variety of spindles used on the 7x Series throughout the range. Most are self-explanatory but it gets a bit weird when you get into the late model stuff that can have ABS or not and/or Dual Mode Auto Locking Hubs (DMALH). Lots of combos...

Rear axle from 1998 Toyota Land Cruiser. E-locker housing but the locker actuator is broken and will need to be replaced. Includes calipers, rotors and pan hard bar. Can ship if you make arrangements with a carrier that is local to me and I just drop it at their yard or they pick up. I have a...

Guys, Need some help, been chasing an oil leak. I thought I had it by replacing the following: -Oil filter housing to block gasket -Fuel pump to block gasket At low speeds (up to 50mph) I have min. oil leak, almost not noticeable. But at fwy speeds, the oil amount that leaks is all over the...

This master cylinder was removed and replaced as preventative maintenance. It functioned just fine when removed. It has 225k miles on it. Price: $400 includes shipping to continental U.S.

1991 FJ80, a while back I had a shop who said they were experienced with Land Cruisers rebuild the front end -- axles, steering knuckles, maybe some other stuff, I don't remember. The axles they used were aftermarket, they have two outboard grooves for a snap ring, I suppose for different...

Hi all. Looking for advice on what to do about the CV Boots I saw leaking on my 2008 4Runner, 132k miles. See photos. Axle with the "CPTD" is passenger side and was replaced by dealership in 2019 when they said the original was leaking. The other/driver side (bottom photo) is original axle...

I’ve searched high, low, left, right and in between. I cannot find anything on the procedure to replace the old brass “seals/bushings“ in the pre 69 front end. I have replacement bushings on hand, the old ball and claw joints are disassembled and I’m ready to install the bushings. Just looking...

I'm sure this has been discussed before but right now I am extremely frustrated on this Christmas Day after installing my third CV axle in 3 months last night only to find out today when I arrived at my family's house for festivities I have checked out the install from last night and discovered...

Used for a few hundred miles on my LX470 but too stiff for my setup. Buyer pays shipping. Only accepting Paypal or cash with local pickup in Tulsa, OK. $100