2f

Okay, super simple power add here, and it took next to no time at all. So I'll admit - maybe no horsepower were gained by the addition of this sweet TEQ sticker, but it is way cool and a direct replacement for the ARB sticker that previously occupied that spot.

I am currently in the process of rebuilding two 2F Aisan Carburetors. One was stamped 5J27 (1975 October 27) and the other 6B3 (1976 February 3). The one built in October 1975 was the original carb for the 2F in the 1976 FJ40, never been rebuilt. The second one (February 1976) I purchased a...

looking for a lightly used (and hopefully still within the allowed tolerances) camshaft, timing cover and the water pump pulley for a clutch fan setup. Thanks everyone!

As the title says.

I'm planning on installing an FJ60 distributor/coil/igniter in my '76 FJ40 and need a dented side cover from an FJ60 (or later FJ40).

Bought for a project that didn't pan out. You'll need to get a new port gasket, but is otherwise in great condition. $200+shipping

Just trying to see what's out there. I've got a decent motor in my 40 right now, although the compression numbers are low. Let me know what you've got and I'll see if we can work out a deal.

hey guys. I need this metal piece. Its going into my 40 with a 2F with FJ60 air intake. Bought the hose new from City Racer. Need the metal piece

I have a stock carb from an '86 2F for sale. It was rebuilt by the previous owner of the engine, and it could use some fine tuning. I removed it to replace it with a desmogged version. Asking $200 shipped

2F water pump pully. This came off a newer 2F with the fan clutch. Doesn't come with fan clutch. $25 plus shipping.

Title says it all. $50 plus shipping.

Looking for the nut for the crank in front of the pulleys.

I've got an issue where once the truck is first started in the morning or becomes cool, it will "pop" once as a misfire on the first real tip in of the throttle. -It wont do it more than once as long as I'm driving in that session. It the engine undergoes a hot restart, it will not pop. It...

Hey guys I need some help with an issue on my '86 2F. I bought it from a guy around 8 months ago. I installed in about 4 months ago and it's run pretty well. Except on my leg of the 40 cross country I was having crazy amount of oil loss. Again the truck runs pretty well and didn't break down...

I accidentally bought intake exhaust manifold for a 1975-1978 2f engine and not the 84' fj60 2f. Looking to sell this one will ship at your cost. Comes with Bolts and Carb Studs. Gaskets are removed and need replaced (but your probably doing this anyway if you have your cracked one off). No...

Hello I am procuring an FJ40 and two 1F engines. One is a SOR rebuilt engine, and the other is the old one with 60k miles that needs some lower end work, but works. I am looking to sell/trade both these 1F engines for a rebuilt 2F. 1f engine by Matt1260 posted Feb 5, 2017 at 6:58 PM1F engine...

I have a 2f in a 1978 fj40 that was rebuilt by PO in 2012. The engine may have 100 miles on it. Now the oil is getting water in it. I am thinking pulling the head and redoing the head gasket and then go from there. What would you guys recommend? Thank You

The Toyota parts diagrams appear to list 2 parts that seal the joints of the 3 piece exhaust manifold for the 2F. Ring gaskets for 2F 3 pc manifold 17151-61010 Gasket springs for 2F 3 pc manifold 17152-61010 I see 2 parts that look like small piston rings in grooves of the end...

Does anyone know what aftermarket carb hats fit a stock 2F carb?

Since installing 3FE exhaust manifolds and losing the 2F exhaust I've noticed that the engine is more prone to rough running when cool to cold. Once the water temp reaches 150F the engine smooths out. The stock exhaust has a provision to warm the underside of the intake as soon as the engine...