2f

1983 2f, complete with bellhousing, weber carb. $300

Crunchy exhaust manifold 2F engine $20 plus shipping

I am just finishing up a 4.3 TBI conversion on my 1976 FJ40. I purchased the kit from AFI and they do not supply an air filter assembly. I want to keep the stock air cleaner if possible which means I will need to come up with an adapter to fit the GM 5 1/8 inch opening up to our @ 3 1/4 air...

As part of a restoration, I am going back to an OEM setup. There are a couple of pin holes and a bit of rust. $75 plus the ride.

The time has come for me to start my swap to a small block LQ4 6.0 and my trusty 2F needs a new home. I'm not sure what to ask for the motor so I'm open to reasonable offers. Motor runs fine, no leaks, new oil pan, new oil pan gasket, new thermostat, never overheated during my ownership. Could...

I have a 2F air cleaner assembly that I will no longer be needing for my engine, came of an 83 engine. Located in western MD, $125 plus the ride. I will get pics up in a few.

Looking for decent distributor, igniter. For 83' FJ60 2F. Send pm please.

1987 2f with 227,000. Head was done about 10k ago by Mudrak. Cost over 2k. This is a fully dressed motor. Compression numbers are 135-140 across all cylinders. I bought this 2F as described above about 1 year ago and ended up not needing it. I have hung onto it because it is an extremely...

I would like to install a header on my 2F FJ4x with unknown power steering conversion. A previous owner installed power steering, it appears to be Toyota parts. The Power steering pump is on the upper passenger side of the engine, so not in the way of the header. The steering box is above the...

Okay - so this is not a build thread per say, but more of a list of what I have done to our FJ60 and an open place for you - the esteemed members of ih8MUD to tell me what I missed and what else I need to do! Here is a copy paste off of my website of what I have done so far. Should you want to...

hi . my 1978 fj40 have a good acceleration in low and medium rpm but poor acceleration in high rpm and engine don't work smoothly in high rpm (may be some cylinder not work in high rpm) and engin and car vibrate in high rpm . in 4th gear engine haven't a good power . but in 1st and 2nd...

Update: To all who inquired and have not received a response i apologize, i've been sick since the holidays and couldnt get out to pull parts, ive decided to list the truck for sale as a whole since i dont have the time or energy to go through it all. asking 3K OBO. 206-556-0123

Hello everyone, sorry if this has been posted previously, I couldn't find anything similar searching. I'm in the middle of a 3FE rebuild, but can't source a composite cam gear for less than $200. I already had a brand new set of steel 2F timing gears, would I be able to use them in my 3FE? I...

****SOLD***** Rebuilt 2F, 4spd transmission and 3 spd transfer case. $1400 obo The head has been milled and its running the Delta Cam that Mark W. suggests. The engine has about 50 miles on it and the trans/tcase combo probably has an unknown amount. The motor runs great, but I had a...

I have a 77 engine with i believe a some issues on the bottom end compression is low it does turn over but knocks I can text a video selling as a rebuild not a running engine I'm in the process of pulling it now can put it on a crate and strap it down and take to a yard to help with...

340k by InTheFace posted Oct 25, 2016 at 1:37 PM2F by InTheFace posted Oct 25, 2016 at 1:39 PM 1984 FJ60. I am the second owner. Still running great after 340,000 miles. Desmogged with JimC carb and dizzy, but decided to be prepared for the inevitable. I bought a wrecked '85 that had a factory...

Hi guys. Believe it or not. A new 2F engine that has never been used and still in its crate. So stay tuned for the un boxing.

Hello everyone I have a 2F engine block that has been professionally cleaned and fluxed. No issues with it at all, only some light rust gouges in one cylinder that should come out with an overbore. I also have the head from this 2F as well, but it has not been cleaned. I have most accessories...

I have a 1984 FJ60 and recently installed a fuel injection system from a 1988 Fj62 into it. everything with the computer seems to be working properly and no codes are showing. We installed a fuel pump (MSD) by the fuel tank and it's pumping out 70psi at the engine bay. The fuel stops at the fuel...