Search results for query: *

Forum search Google search

  1. David Rodgers

    Block surface dots

    You know, I’m sure it’s my bad throttle cable because a have adjusted my idle for years :). No kidding, it seems like in the winter, I have to turn it down. I just adjust (loosen or tighten) the nuts on the throttle cable and adjust it where I want the idle rpms and it stays until the season...
  2. David Rodgers

    Block surface dots

    Let it cool. No leaks, fluids look good.
  3. David Rodgers

    Block surface dots

    My throttle cable is toast also, it needs to be replaced. I pulled it off the throttle body. I adjusted the nuts to lower the rpms. You’re right though, with all the new stuff on the truck, I’m sure it will take a while. I’ve had a check engine light on this since I bought it 14 yrs ago :)
  4. David Rodgers

    Block surface dots

    I just let it fully heat up. I ran it for about 20 minutes. Everything seems fine. I had to hold my breath and go in and check on it. Fan cycled twice. I could hear it. Temp stayed solid, oil pressure solid. No visible leaks. I’m going to let it cool and check levels again. No check engine...
  5. David Rodgers

    Block surface dots

    Just went out and checked for leaks. No leaks.
  6. David Rodgers

    Block surface dots

    Probably a few days. I’m gonna buy another center light bar and make the wiring harness. I’m also cleaning up the hood and painting part of it. Also painting the front grill and gluing two broken head light brackets. No insurance on the truck either. I turned it off since I knew it would sit...
  7. David Rodgers

    Block surface dots

    Man, you can catch a buzz quick:)
  8. David Rodgers

    Block surface dots

    Ok, could not wait. Turned the key and let it sit to pressurize fuel. Started up immediately. Great oil pressure and running fine. Idle a little high. Did not let it heat up fully since it’s in the garage. No check engine light now. Opened windows and door. I still have the hood off and the...
  9. David Rodgers

    Block surface dots

    Changed oil, added coolant, power steering fluid , transmission fluid still looks good, I’ll check again after I crank. How should I crank (don’t say...turn the key). :) Any best method or procedure? The battery is in and I turned the key to acc (power is on). Almost turned it one more but...
  10. David Rodgers

    Block surface dots

    What a major pain...pulling transmission lines off to replace the hose clamps. Took hours :) I had the oem clamps and they were too loose. Feel better about replacing them. I used the EFI hose clamps because they don’t tear the hose and you can tighten.
  11. David Rodgers

    Block surface dots

    Yea, you’re right. That thing was junk. The one that I have (before that one) was in way better shape. I thought the one that I bought would be in better shape and it would be dry (so I could paint). Mine was sopping wet with ps fluid. In hindsight, I’ll never buy from them if this is what I can...
  12. David Rodgers

    Block surface dots

    I might use EFI clamps.
  13. David Rodgers

    Block surface dots

    Transmission lines/radiator/shroud are really fun :) I used the gates 3/8 transmission cooler lines and they are fun getting on the nipples (even with transmission fluid on them). After struggling to get them on, the spring clamps seem loose (hose tight as crap, clamp loose). I used the oem...
  14. David Rodgers

    Block surface dots

    I replaced the transmission lines (and a bunch of fluid). I’m gonna replace through the dipstick, should I also fill the transmission cooler (pop the top line and fill)? thanks for any info
  15. David Rodgers

    Block surface dots

    I’m gonna change the oil and filter. Then run it a couple days and then change it again.
  16. David Rodgers

    Block surface dots

    Thanks. It has been a lot. Hope it runs well :)
  17. David Rodgers

    Block surface dots

    Waiting on radiator, gotta block that pair tube
  18. David Rodgers

    Block surface dots

    Throttle body on, power steering reservoir Ordered from cruiser parts...that thing arrived and was in terrible shape. I had to grind, steel brush, hand sand that thing to get the rust off. Spark plug wires, oil catch can, various vacuum lines, new air filter, new fan clutch ( started rebuilding...
  19. David Rodgers

    Block surface dots

    Please let the eagle run (or fly :))
  20. David Rodgers

    Block surface dots

    Hard to torque bolts with a 2.5 foot extension, laying on your back with and old gauge style torque wrench 2 inches from your eyeball.
Back
Top Bottom