Search results for query: *

Forum search Google search

  1. troopie

    VNT turbo differences

    I'm looking to get a brandnew VNT turbo from Impex-jp. Now when i look at the partnumbers, i should have 17201-17070, but they don't list that, only 17201-17050. After some searching both those numbers appear to be VNT turbos for a 1HDFTE. Does anyone have the knowledge to know if those turbos...
  2. troopie

    12HT/2H crank question

    Unfortunately i have nothing left out of a 2H of 12HT. The harmonic balancer should swap over. The crank itself should also perform in a 12HT, the only thing i would be worried about is breaking the crank. That's what happenend to mine years ago. It broke in a spot with more meat then a 2H...
  3. troopie

    12HT/2H crank question

    I've had 2H and 12HT cranks side by side. They would definately swap out, but the 12HT crank has more meat in some areas. Not all, but some off the journals have a wider casting. Not sure if my explanation makes sense. ;)
  4. troopie

    The Official 1HD-T/FT Fuel Pump Mod Tuning Thread

    I have one. Material is too soft. I guess it's "just" stainless steel. I upgraded to a KOC one out of Japan which is made out of better material and the profile is a tad bit wilder ;) I should have a picture somewhere of the stock, euro4x4 and KOC pin.
  5. troopie

    The 2H/12H-T/1HZ/1HD-T/1HD-FT Gturbo Alternative Tech Thread

    I have a cheap ebay mbc. I had it on my 12ht for years without issues. However on the 12ht i could use a very short hose from the turbo to the wastegate actuator. On the 1hdft i had to use use a much longer hose due to the positioning of the turbo. The spike could very well be caused by...
  6. troopie

    The 2H/12H-T/1HZ/1HD-T/1HD-FT Gturbo Alternative Tech Thread

    I've got the same turbocharger on my 1hdft. I experienced the same fluctuations like you have. However i have a mamba wastegate actuator. I thought using that would help setting boost better than an mbc. I was wrong, it caused those weird fluctuations. I ended up shimming it and using an mbc...
  7. troopie

    1HDT boost compensator adjust, now no throttle response

    Did you accidently push off the rod that goes from the accelerator cable to the pump? Don't ask me how i know.... LOL.
  8. troopie

    The Official 1HD-T/FT Fuel Pump Mod Tuning Thread

    Thanks! I didn't have the most helpfull dude at the diesel specialist, so this helps.
  9. troopie

    The Official 1HD-T/FT Fuel Pump Mod Tuning Thread

    Ok, i wasn't aware of that. I'll have the dieselshop measure the plate for me and then i'll know.
  10. troopie

    The Official 1HD-T/FT Fuel Pump Mod Tuning Thread

    I've had some dirty diesel thru my pump and pulled it to have it checked out at the diesel shop. The feed pump rattles like crazy. Now since it's out, i might do some mods anyway.... Any thoughts on or experience with higher lift camplates? Such as fitting a 2.8mm or 3.2mm lift Cummins 6BT...
  11. troopie

    Differences in HF1A tcases

    I'm a bit late to reply. Yes the fzj105 gear is one piece with the shaft. You could pull the bearings off of the hzj gear and press them on the fzj gear. To plug the shaft, somehow it's hollow, you can use a plug out of your old full time case.
  12. troopie

    12HT real time help

    @rideglobally These are standard bearings. Any bearing supplier should be able to get them. There's number on the bearing, that number is enough to get it. Don't quote me on this, but i believe it's a 6302 bearing. It's to long ago to clearly remember and i don't have a 12HT anymore to check.
  13. troopie

    12HT real time help

    The bearings in the pulley can be replaced pretty easily. Any bearingshop should be able to hook you up. Glad i could help!
  14. troopie

    12HT real time help

    Have you checked the powersteering idler pulley? That little bearing can cause some serious noise troughout the entire engine.
  15. troopie

    12HT shutoff up steep hill

    Sounds like the shutoff vsv (vacuum switching valve) not getting power. A bad connection can do this for instance. Take off the connector of the vsv mounted on the back of the crossover pipe and check if thats clean. Hth Mark
  16. troopie

    The "Official" 1HZ/1HD-T/1HD-FT Airbox/Intake Mod Thread

    @mudgudgeon Yes, it will probably look ghetto....
  17. troopie

    The "Official" 1HZ/1HD-T/1HD-FT Airbox/Intake Mod Thread

    So in a quest for an affordable high flow airbox, i've been thinking of using a "type a" airbox out off a UZJ100 (17700-50170) and modifying the in and outlets with 4 inch in and outlets. Shipping and import taxes are way to high to just go ahead and order one of those fancy ones from down...
  18. troopie

    12ht rebuild an tuning

    I would drop off the injection pump at a specialist. They can bench test the pumps to. It's useless to replace one thing and find out that there are more issues with the IP. Just my opinion offcourse. Mark
  19. troopie

    12ht rebuild an tuning

    The 80 series has an MLS head gasket standard.
  20. troopie

    Need part ID on IPZ injector pump

    That looks like the powersteering pump to me. Located below the injection pump.
Back
Top Bottom