Search results for query: *

Forum search Google search

  1. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    So that is just shy of 3 foot pounds. I wonder why I never stumbled on that. I do not think my manual includes the 3F. Good find. :cheers:
  2. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    I have seen that before when I have pulled a crank. I was unsure if that was factory or from a rebuild but it is likely factory.
  3. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    There is another thread about head bolt torque that includes a discussion about re-using head bolts and if they should be lubed and re-torqued here in the 40 section. Sorry I do not immediately have the link to offer but if you can find it it is worth a read.
  4. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    Put a little sealant on either side of the aluminum washer.
  5. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    I just looked and did not find one. However, the FSM listed a torque for the A440F (FJ62 Auto) drain plug as 15 foot pounds (pg AT-5) in one section and 20 in another (pg AT-20). Interesting. Here are the only torque specs listed for the H41 and H55 in the FSM: H41/H55 Transmission...
  6. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    Here is another useful thread to muddy the waters a bit. Found in the FJ60 FAQ https://forum.ih8mud.com/showthread.php?t=129878
  7. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    Generally if there is no specific torque listed anywhere, I use the generic chart. I just replaced my sidecover gasket and without specific specks I figured I would torque it the same as the oilpan...WRONG ANSWER. I think I ended up at about 4 foot pounds. I just tightened them down until the...
  8. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    Torque Adapters How to compute torque If an adapter is attached to the square drive of a torque wrench, the wrench will not give the actual torque indicated by the setting of the handle. A simple formula however, allows you to figure out what the setting should be to deliver a pre-determined...
  9. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    My only possible reply is that is what the FSM said. I didn't make anything up - just assembled the info into one easy to find place :shrug: I know some folks say even just go hand tight on those. If you check you will find some specs different in the various manuals. :shrug: x2:cheers:
  10. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    Thanks guys. I am expecting a new 2F FSM in the mail any day now. If I see anything in it I have not posted I will update this.:cheers:
  11. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    And finally (and probably more importantly) some generic sites on metric bolt torque: Metric Torque Specs for Fine and Course Threads Iron and Aluminum The FUTEK Online Metric Bolt Torque Calculator A 2 Page PDF that includes a computation for surface condition (more then you need)...
  12. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    Here are some decent Web Sites I have come across for SAE threaded bolts as I have been doing this: U.S. BOLT TORQUES SPECIFICATIONS AND FACTORS For the real Engineer - The FUTEK Online Torque Calculator Torques for SAE Grade 5 and 8 Fastners (oiled and dry) SAE Torque Specs...
  13. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    Max Ellery’s Land Cruiser Repair Manual 1969-1990 (FJ & RJ) (Second Half of the above post) Transfer Systems J30 Transmission Companion Flange Nut 102-122 f/lb Backing Plate Assembly 22-32 f/lb Emergency Brake Drum Nut 102-122 f/lb Transfer Systems for Other Transmissions (4 & 5...
  14. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    Max Ellery’s Land Cruiser Repair Manual 1969-1990 (FJ & RJ) This manual is the most difficult to find specs in as they are not listed anywhere but in the procedures themselves which is great for using the manual step by step but it provides more torque specs then any other I have seen. Here...
  15. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    I believe Alldata is a pay service so unless you post a screen shot, a link won't work.
  16. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    1969 – 1971 Toyota FJ40 Chassis & Body Manual Clutch Clutch Pressure Plate Laver Pin Yoke Bolt 25-30 f/lb Clutch Cover to Flywheel 15-19 f/lb Xmsn & Xfer Case Transmission Set Bolt 52-57 f/lb Gear Shift Cam Retainer Set Bolt 11 f/lb Xfer Case to Xmsn 2 Long Bolts 20-28 f/lbs Xfer...
  17. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    F Engine Toyota Repair Manual Torque Specs. (1988 Reprint) Cylinder Block Cylinder Head 83-98 f/lb Crankshaft Bearing Caps (Front, Second & Third) 90-108 f/lb Crankshaft Bearing Cape (Rear) 76-94 f/lb Oil Pan 4-9 f/lb Oil Pump 7-12 f/lb Cylinder Head Lock Support 10mm bolts and nuts...
  18. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    "Generic" Torque Specs From the FSM Here are the Generic Torque Specs from the Back of the F Engine FSM. Scan was easier then retypeing this as they were all in one place - I hope Toyota won't be pissed!
  19. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    It is late on the East Coast so when I have an opportunity I will be glad to load the FSM Torque Specs as well as the Generic Torque Specs listed in the back of the FSM and else where. HAVE ANY RELIABLE LINKS TO TORQUE SPECS???? LINK 'EM HERE! If you want to list a "Gutentite" please...
  20. Hugh Heifer

    Misc Torque Specs - Use at your own risk! (FAQ)

    I also came across this from AutoZone and it appeared very useful if correct:
Back
Top Bottom