I'm so over the stock heater in my 1981 60, it never worked worth a dam when it was working.... the heater core started leaking, tore the dash apart and had it fixed at a radiator shop.... started leaking again.... and yes i tried all the crap on how to fix/upgrade the stock heater and none...
SO I WAS LOOKING AT IS VIAIR SET UP FOR MY CRUISER. I WAS THINKING ABOUT MOUNTING IT ON THE DRIVER SIDE IN THE REAR CARGO AREA, KINDA SUNK INTO THE SIDE PANNEL A LITTLE AND BUILD A COVER PANNEL TO HIDE THE REST... ITS 200 PSI WITH A 2 GALLON TANK AND 100% DUTY CYCLE
VIAIR Corporation - 200 PSI...
SOLD>>>>>>>>>>>>>>>>>>>>>>>>>>SELLING MY CAMPING LABS RTT, IN LIKE NEW CONDITION!!! THE WIFE HURT HER BACK AND GETTING IN IT IS HARD FOR HER NOW AND WONT BE ANY EASIER AFTER SURGERY.... IT 57 X 96 INSIDE LOTS OR ROOM. IT ALMOST EXACTLY THE SAME AS A TEPUI... IF YOUR CLOSE ENOUGH I WOULD...
i have been searching all over and everyone seams to avoid posting any info on the question i have
so here it goes... i have a 81 fj60 that i'm in the beginning of my 5.3l vortec swap, so i bought the AA 50-0408a kit and got it all bolted up to my trans and rebuilt my t-case. bolted everything...
so i'm getting ready to tear into my swap and getting the last little bits of parts and pieces rounded up... looking for any tips and tricks from guys who have been down this road before me, i'm trying to have as many of my parts in front of me as possible. i'm swapping to a 5.3 ls with a...
so im wondering if the third member from a fj40 will work in my fj60 housing i have a buddie that is giving me a set of fj40 axles that are 4.10 with lockers if i want them...
trying to decide on a locker setup for my 60. thinking about aussie lockers, but i have heard that auto lockers are dangerous on the snow and ice in a daily driver??? i know that the arb's are a good choice but not sure if they are in my budget
IM GATHERING PARTS FOR THE UPCOMING SWAP IN TO MY 81 FJ60. I HAVE BEEN LOOKING FOR AIR INTAKE SOLUTIONS AND I WAS WONDERING IF ANY ONE HAS USED THIS OR ANY THING SIMILAR. https://www.airaid.com/U-Build-It_intake_systems.aspx
so im getting ready to start overhauling my suppension and drive train. i plan on a 5.3l/4l60E swap but after that im starting to over think stuff do i build the cruiser axles? 14bolt? dana 60? i plan on lockers and at least 35's possibly 37's im gonna do a soa lift.... are the...
i was replacing the thermostat in my cruiser tonight... and the previous owner had put installed it with silicone and while trying to separate the housing the tab were the lower housing bolts to the block snaped off :doh: .... im in desprate need of a new lower thermostat housing man-a-fre...
im planning on doing a vortec swap in my 60, i know alot of people do the 5.3l and 6.0l but any one done a a 4.8l??? the 4.8 rated at 290 hp and 305 ftlbs compared to the 2f 135 hp and 200ftlbs ... found a couple under 50k 4.8's with the transmissions wire harness and ecm for under 1500.00...
i work at a toyota dealership and just got my first fj60 i ran the vin number through the tis system and there is a open recal for it... guess im getting a brand new gas tank and all the goodies that go along with it (almost 2000.00 retail ) nice little supprise for a friday.... so if you...
i freind of mine has a cnc plasma table and we are going to be building the bumpers for my fj60. i know there are shops that build some bad ass bumpers but they are expensive, i understand time and cost of materials. and the cost of shipping them pushes them out of reach for many of us...