Search results for query: *

Forum search Google search

  1. jdhall3

    JD Rebuild

    Everything seems to working well with most of the bugs getting ironed out. For a quick update... Motor rebuilt for 9:1 downey torque cam downey springs (and a whole lot of look pretty stuff) The powerband is much more useful now. 191ft pounds at 1600 RPM is really nice for...
  2. jdhall3

    JD Rebuild

    hooked up should be running today...Ill try to keep you updated. :bounce2:
  3. jdhall3

    JD Rebuild

    One of the reasons (and there were a few) that we went with the f head is there is no galley plug.
  4. jdhall3

    JD Rebuild

    So far no damage that we can tell. It only had about 8 miles when I noiticed the noise the motor was making. The landcruiser was very kind in unscrewing 2 of the valve screws and that you use to to the valve job making it only run on 4 cylinders and if you couldn't notice that noise coming...
  5. jdhall3

    JD Rebuild

    Well here is what were doing to get the oil to the head... F head to 2f block From there we are routing to the rocker arm rail via copper line. Thanks and sorry it took so long to update.
  6. jdhall3

    JD Rebuild

    Ok...no dyno yet. I'm sure some of you know about putting a F head on a 2F motor there is a oiling issue for the rocker arms. :o Well......I didn't realize that until it was making some noise. Now that we have figured out how to oil the rocker arms I will try to post the steps....then we can...
  7. IMG 1441

    IMG 1441

    • jdhall3
    • Media item
    • Comments: 0
    • Album: the truck
  8. IMG 1435

    IMG 1435

    • jdhall3
    • Media item
    • Comments: 0
    • Album: the truck
  9. IMG 1441

    IMG 1441

    • jdhall3
    • Media item
    • Comments: 0
    • Album: the truck
  10. IMG 1435

    IMG 1435

    • jdhall3
    • Media item
    • Comments: 1
    • Album: the truck
  11. the truck

    the truck

    • jdhall3
    • Album
    • Comments: 0
  12. jdhall3

    JD Rebuild

    Yeah I knocked the right one off climbing up in the engine bay...I just stuck it back on real fast. Then I saw my pictures and said nobody will notice. ha
  13. jdhall3

    JD Rebuild

    Well she made it home...looks like dyno will have to wait till Monday. I will post results as soon as I get them.
  14. jdhall3

    JD Rebuild

    If you want a more detailed shot let me know...he are a few over view shots. Should hit the dyno tommorow. I will post what I get. Shouldn't be too earth shattering but it has to be better than it was. I thought this was a pretty cool spot for the controls for the...
  15. jdhall3

    JD Rebuild

    No problem...the engine is running now. I just need to bleed the breaks. Then Im hopefully put it on the dyno today to see some numbers. Then Ill bring it home for the full photo shoot of the bay. Give me a little bit. I must say I never thought it could look this good.
  16. jdhall3

    JD Rebuild

    Quick shot of the motor in the truck..I need to tuck some wires and fire it up! Ill try to go get better shots later.
  17. jdhall3

    JD Rebuild

    I ask the same question when I rolled it out for a couple pictures... I was told "it held it when when took it out so now it should weigh less because theres no dirt it her"...ha ha :flipoff2:
  18. jdhall3

    JD Rebuild

    Sorry its been awhile here is the updated photos...Hopefully should start going in the truck in a day or two. Right now like I said before, were going to break it in with the carb before we add fuel injection. Also I'll check on that crank question you had.
  19. jdhall3

    JD Rebuild

    Finishing up the inside of the engine bay...painting the frame with a couple coats of rust-o... Next the engine goes back in and rerouting some cables.
  20. jdhall3

    JD Rebuild

    ...motor is 90% done...just have to finish a few minor bits and stick it back in the truck. Im guessing a week at the worst. Then the plan is too break-in the motor with the weber carb. and stock air intake. I would like to do a dyno run sometime after I have some miles on the new motor...
Back
Top Bottom