Search results for query: *

Forum search Google search

  1. skip96lc80

    P0720 code - Output shaft speed sensor

    All, My '96 LC decided to throw the P0720 code in addition to the P0500 code. I verified that the speed sensor on the TC looks to be in working order, but I'm not quite sure where the output shaft speed sensor is located. Is this the same as the No. 2 Speed Sensor on AT-005 in the FSM...
  2. skip96lc80

    Parking brake rebuild

    All, I will be re-building my parking brakes and I have followed the @Poser posts/FAQ but I haven't been able to track down the part numbers for these bolts, they weren't listed in the parts list for the rebuild. I've investigated and looked on different part sites but haven't been able to...
  3. skip96lc80

    Parking brake?

    This post has been extremely helpful as I will be re-building my parking brake due to the same issues seen on here but I have a question as to parts. Looking for the part number(s) for these bolts that attach the mounting block. I've investigated and looked on different part sites but haven't...
  4. skip96lc80

    Rear Brake & Parking Brake Guts Help?

    I personally use CRC Synthetic Caliper Grease. Getting those caliper bolts out can be a chore when they've gone dry. One of the reasons they're not coming out is that there wasn't/isn't enough grease in the boot and slide bushing to begin with when they were last done. Whenever you replace...
  5. skip96lc80

    Metallic grinding noise after buying new tires.

    I had my tires done at the local Discount Tire, from what I could see they did it right, minus this issue. I checked the backing plate and inner side of the wheel and didn't see any wear or shininess that would indicate rubbing. Just in case today I pulled the wheel and rotor off to see if the...
  6. skip96lc80

    Rear Brake & Parking Brake Guts Help?

    Did you lube your caliper pins before putting them back in?
  7. skip96lc80

    Metallic grinding noise after buying new tires.

    That's what it sounds like to me. Didn't even think of this, I was already starting to grumble about having to do the hubs. :) Thank you! I'll pull the wheel and align the discs, and put the wheels back on. --skip
  8. skip96lc80

    Metallic grinding noise after buying new tires.

    Just rubber.
  9. skip96lc80

    Metallic grinding noise after buying new tires.

    All, I just purchased new shoes for my cruiser, went from 265/70/16 to 285/75/16's. Now it sounds like I'm getting a metallic grinding noise coming from my rear passenger side, never had this issue before with the smaller tires. There's no rubbing and I have a 2.5 lift from OME installed...
  10. skip96lc80

    Front brake pads sitting high on the rotor and a very hard to diagnose creaking from the front end.

    I'm having the same issue, but only about 1/16th of an inch overlap. I did install new rotors but before I changed them I put them on a side by side comparison to make sure it was the exact same and compatible, caliper bolts snug. The only other thing I can think of is to replace with new...
  11. skip96lc80

    Front brake pads sitting high on the rotor and a very hard to diagnose creaking from the front end.

    Did you figure out what the issue was?
  12. skip96lc80

    Wanted  FZJ80 Header Panel

    Looking for a 1996 Front Header Panel. Mine cracked and broke on the passenger side, and is now pointing my passenger headlights towards the ground. Thanks.
  13. skip96lc80

    ABS Relay - point me...

    Thanks for the assist Dugsgms!!
  14. skip96lc80

    ABS Relay - point me...

    '96 LC, looking for where the ABS relay is located, photo's are best. The diagrams I have are the crudely drawn one's and don't help much when looking for stuff under the hood. Thanks!
  15. skip96lc80

    Transmission sensor?

    Never mind after some digging I found what I needed. Thanks for the answer LandCruiserPhil!!
  16. skip96lc80

    Transmission sensor?

    Thanks. Now that I know what it is, I have the ends of the wires loose but not sure if the harness is plugged in or if it fell out. I can't tell.
  17. skip96lc80

    Transmission sensor?

    LOL. As long as it doesn't affect the emissions or possibly wrecking my trans by not including it. I'm okay leaving it alone.
  18. skip96lc80

    Transmission sensor?

    I recently bought a '96 LC 3xLocked with a swapped out 1FZ-FE engine from a '96 Lex450. I found a bit of wiring from the harness that was unplugged. Can someone tell me what exactly this is supposed to be? Thanks.
  19. skip96lc80

    O2 sensor (what to buy?)

    was there ever a part number for the 95-97 o2 sensors?
Back
Top Bottom