Search results

  1. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Here is the kit I picked up. https://www.pscmotorsports.com/replacement-parts/psc-hk2040.html You just need to pick up an "SF06" fitting for the steering box input
  2. StevoJonesFJ60

    Stevo's '95 4BTRunner

    So true, and fortunately since the distance is short for these lines, vs a full size truck, I have always had enough leftover from the kit to make another line if needed.
  3. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Things have been busy with work, but the truck is coming along too, spent some time getting the batteries, starter and hydroboost. I salvaged some 4/0 wire from a loader I helped pull the engine on. So I used that to tie in the batteries, definitely overkill in the size department but free is...
  4. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Work has been busy so I haven't had as much time to work on the truck as I would like, but I was able to knock out a few things to keep the project moving. I dropped the fuel tank again, hopefully for the last time. I was checking the ohms on the ford sending unit and realized that it would not...
  5. StevoJonesFJ60

    Stevo's '95 4BTRunner

    I had some time to fabricate an intercooler mount, being that I am just going with the single turbo for now I grabbed something simple, but still a decent size. Drew a base plate to mount to the existing front clip. Made a bracket to hold the intercooler Tacked it up, then installed the...
  6. StevoJonesFJ60

    Builds Build #2 - Now with a iForce 5.7 3UR and AB60 6 Speed Auto

    This is an amazing build, I would love to have the space you do. Keep up the great work. Can't wait to see it finished. I will definitely be copying some details from your front bumper for my build.
  7. StevoJonesFJ60

    Stevo's '95 4BTRunner

    So upon further reflection, I will be holding off on the compounds for the time being. They will definitely be something I want to do in the future, but in order to make them work well now I would need to add too many additional things to the build. The Engine would need studs, the LP turbo...
  8. StevoJonesFJ60

    Stevo's '95 4BTRunner

    That's what I was hoping to hear!
  9. StevoJonesFJ60

    Stevo's '95 4BTRunner

    For when I do get head studs, which are recommended the ARP2000 series or the ARP625+? Just so I can figure out how much to start setting aside for them.
  10. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Thank you very much, yeah definitely will be progressing with lots of tuning. I know it will take a while to get it dialed in and should have just done studs from the start. Good to hear the 4bt oil pump should hold up, and thanks for the tip about overtorquing the head bolts, I will...
  11. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Hey thanks for the quick reply, I'll plan on running the stock 4bt stuff for now in terms of oiling, if my pressures are low I can always swap in a 6bt pump. I'll plan on swapping the 14cm2 onto the hx35 and see how that works. I have decent sized intercooler, but I wont be able to see how it...
  12. StevoJonesFJ60

    Stevo's '95 4BTRunner

    So a question for some of those that have been running compounds @GLTHFJ60 @boots4 @The Phoenician I have read through a bunch of the compound turbo threads over on 4BTSwaps, and have noticed that in time things seems to be shifting as to being "required" or not for running a compound turbo...
  13. StevoJonesFJ60

    Full width axle front shackle mount

    I made some custom frame outriggers to put a full width SDD60 under my 4runner. I did slider boxes but the same style outriggers could be used for your shackle or spring mounts. Its in my build, post#6.
  14. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Thanks, its been a fun pandemic project for me. I'm really hoping to get this wrapped up by the summertime. Can't wait to drive it around.
  15. StevoJonesFJ60

    Stevo's '95 4BTRunner

    I figure I wont have to worry about it choking at higher RPM, I do have a 12cm2 housing, but according to what I have been reading on 4btswaps, the 14cm2 would be a better fit for the super hx30. Eventually I was going to do head studs and the compounds, this just gives me an excuse to do the...
  16. StevoJonesFJ60

    Stevo's '95 4BTRunner

    And while I was digging around in the random parts I had accumulated, I happened upon a 14cm2 wastegated housing for a HX35. Then I got to thinking if one turbo is good, surely 2 would be better? I have a HX35 that was free from a friend, I also have plenty of room above my starter to make all...
  17. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Batteries needed a home in the fenders so I drew up a couple battery boxes, cut em out and welded them up. Nice secure fit for my battery size: They fit nice in the fenders. Painted Set in place, once the paint dries ill bolt them in and get the batteries in their permanent homes.
  18. StevoJonesFJ60

    Builds Dirty Koala Build - Cummins 6BT + NV4500 + HF2AV Swap

    Just read through this thread, really nice work with lots of great tech too. Any updates on the build?
  19. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Next thing on my list is to get the engine ready to fire off the key, so I had to come up with some radiator lines. I am going to do a full system flush, my heater core is a little blocked up so hopefully I can backflush it and get that working. Fortunately I had some old hoses around to...
  20. StevoJonesFJ60

    Stevo's '95 4BTRunner

    Radiator is back from the shop, I paid to have the bottom port moved from the left hand side to the way bottom. If the "through-flow" doesn't send enough coolant to the left hand side of the system, I'll install a "scoop" to divert the flow that way. Installed: I will be switching to a...
Top Bottom