Search results

  1. Jprice

    Part ID Help

    Again, a big thank you to everyone who responded. I got the new filter on and did notice the engine running a good bit smoother. Hoping it may even translate into 1 or 2 mpg gain.
  2. Jprice

    Part ID Help

    Awesome! Thank you so much, Beno! As can be seen from the pictures, mine has broken. The PO did a glue job on it, for some odd reason. Am I safe to drive around a bit till I can get a new one connected? Or could this risk damage?
  3. Jprice

    Part ID Help

    Hey Cruiser's, I am looking for some help identifying the part in these pictures. I apologize for my ignorance. I am not much of a mechanic but I am trying to figure this stuff out. I tried looking on some exploded views and think I may have identified it as a PN# 9091711022, but I wanted to...
  4. Jprice

    Parting Out Parting out 93' through 97' FZJ80 / LX450

    I am possibly looking at replacing a rusty rear axle in my 97. Is your "One rear diff housing - $400" compatible with the factory locker? IF so, do you have any other of the surrounding parts, ie panhard rod? I have a rust problem that is concentrated around the rear axle and I'm trying to see...
  5. Jprice

    Parting Out 97 triple locked LC front end rear quarter damage

    If the complete rear axle has not been spoken for, I may be interested. How much?
  6. Jprice

    Need advice on installing air conditioning on my home

    Is the door to the patio room always closed? If so, then yes, it would not really need to be included in the load calculation. If it is open or if it has any kind of louvered vents or even if it is an interior door "hollow", then it absolutely would contribute to the load of the house, as air is...
  7. Jprice

    Need advice on installing air conditioning on my home

    Not a lot of experience with Swamp Coolers but I do know ductwork. A) do you think that adding an evap coil without replacing the furnace is a good idea? ~Not if the sizing is mismatched. Your current furnace is only delivering so much CFM, and if it is paired with an Evap coil designed to...
  8. Jprice

    BH3D Cup Holder - PWR 2nd Switch Relocation?

    I would certainly do that if I had any. Alas, the Lexus console doesn’t have them. I should’ve mentioned that in the first place.
  9. Jprice

    BH3D Cup Holder - PWR 2nd Switch Relocation?

    Yeah, I'm not sure which way I'll go. I just like the idea of keeping everything clean and neat looking and I also worry about condensation dripping down and messing with the switch in its current location. I will likely try making and extension and moving it up. If I do, I'll be sure to post...
  10. Jprice

    BH3D Cup Holder - PWR 2nd Switch Relocation?

    I do appreciate the responses and I do understand that the buttons are still partially visible and still functional but I would really like to move the switch up and away, if possible. I did try positioning the unit farther forward but then you sacrifice in height as you approach the ashtray...
  11. Jprice

    BH3D Cup Holder - PWR 2nd Switch Relocation?

    Hello all, I just received my Dual Front Cup Holder, from Brad at BH3D and was wondering what you all are doing with the PWR/2nd Switch, that gets mostly covered up by the holder. My initial thoughts were to relocate the switch to somewhere up on the dash but noticed that it is on a pretty...
  12. Jprice

    15% off coupon and new prices on my website

    I just got a tracking number this morning. Thank you Brad, for such quick turnaround. I will be sure to post up some pictures once I get it installed!
  13. Jprice

    15% off coupon and new prices on my website

    I was hoping Santa would be bringing me a cup holder or two but alas I had to get my own. :-) I just placed an order for front and rear cup holders as well as the bezel and cell phone mount. Can't wait to get it all in and mounted. Thanks for making such a cool product for our trucks!
  14. Jprice

    Double shift indication - shifting into D engages L instead = FIXED!

    JCruse, I just wanted to say thanks for the information on this thread. I had the same symptoms as you described and upon my initial search on Mud, I didn't think I was going to find any answers. After much digging, I came across this one and bamm! Swapped the NSS and all is well again. Thank You!
  15. Jprice

    Rear Axle Help FZJ80

    To everyone that has responded, I would just like to say thanks. I recently come from the Jeep world, “actually still have the little TJ” and got a lot of use from various forums and members there. I was really hoping to find something equivalent for this new ride and I must say that I am...
  16. Jprice

    Rear Axle Help FZJ80

    Well, I do appreciate your honesty. So I guess the general consensus here is that my axle is not too far gone and a good blasting and recoat should suffice. That is good news, I would say. Thank you, to everyone who chimed in. I suppose I will give that a go. Is there anything else that I...
  17. Jprice

    Rear Axle Help FZJ80

    zzdenis, I love your optimism! He is just stating that he doesn't know how deep the rust goes and therefore he would prefer to replace it. He has offered to drop it, blast it, and reinstall but for the price he quoted me, I think I may be better off looking for a replacement. Davidp, I can't...
  18. Jprice

    Rear Axle Help FZJ80

    Alright, hopefully I can get these pictures to post. Baldilocks, I think you may have pegged it. The front is nowhere near as bad as the rear. Your hypothesis is the only one that makes sense. Slow95, I will be contacting you shortly, to see what kind of a deal we can work out. My mechanic is...
  19. Jprice

    Rear Axle Help FZJ80

    Thank you all, for the responses and insight. I am meeting the mechanic this afternoon. I will take pictures and post them up for your further evaluation. I really hope it's not as bad as he is making out. I absolutely love the truck. What is really odd to me, is that when I was researching...
  20. Jprice

    Rear Axle Help FZJ80

    I’m sort of asking myself the same thing. I plan on going to his shop tomorrow to see if I can’t better assess how extensive the rust is. I’ve seen it up on a lift only briefly and I didn’t see anything that lead me to believe it was that bad. I will try to get some pictures and post them up...
Top Bottom