Search results

  1. slow91fj90

    2008 Harley Davidson Crossbones Northern Virginia

    2008 HD Crossbones with 9k miles for sale. Recently had the 10k service and a new rear tire installed. The 10k service included a complete adjustment of the springer front end and replaced any worn our parts. Aftermarket stuff installed is listed below: --Vance and Hines RSD Tracker 2-1 --HD...
  2. slow91fj90

    Castor correction bearings?

    Anyone have any experience with these? I was ordering some parts for my Tacoma and stumbled across this. I think I have a castor problem, but will have to get some numbers from a alignment to find out. http://www.lightracing.com/component/spc/?task=part_description&pid=88920
  3. slow91fj90

    1991 FJ80 37's, 529s

    Well I thinks it time to let my baby go. I dont ever get to use it for what I set it up for anymore. Here are the detail. 1991 FJ80, 170k. Truck runs good, no known issues. It does have a steering wheel shake at certain speeds, around 40-45, started doing it when I put the swampers on. Anyways...
  4. slow91fj90

    Wanted  WTB Passenger side mirror 80 series

    Looking for passenger side mirror for 80 series, black if possible but not a deal killer if not. Thanks, Matt
  5. slow91fj90

    Wanted  Spindle for 91 80 series

    Looking for a good used spindle for drivers side (not sure if that matters). Thanks
  6. slow91fj90

    Time to retire the 80

    Well its been since January of 2000 when I first laid eyes on it in San Diego, I knew I had to have it. Bought it and haven't looked back. I remember I always wanted 80 series but didn't know about 3FE's and 1FZ's. I didnt care, it was love at first sight. I snatched her up with 60k miles. Here...
  7. slow91fj90

    For Sale  H151 5 Speed and transfer case

    I have a H151 with only 12k kilometers on it. I have the clutch and pressure plate also. Here is a pic of what I have. The trans comes with everything in the picture except the ECU and the starter and instrument cluster. Drive shafts and center console are included. Also in the picture is the...
  8. slow91fj90

    Checking interest on a H151 5 speed and transfercase

    Hey 100 series guys, I have 5 speed with tranfer case still bolted to it out of a 100 series from overseas. I have the shifter console for the interior. I am just posting this here to see if there is any interest for it to sell. I was gonna use it for a project but got other plans now. It only...
  9. slow91fj90

    Toyota parts on back order?

    I went down to my local dealership to order new spindle nuts and the locking tabs on Tuesday. Well they called me and said they are on national back order. Anyone else had any issues with getting special order parts? I need a set for one spindle before next week end so I can go wheeling. Anyone...
  10. slow91fj90

    Diesel Swap

    Hopefully I haven't bitten off more than I can chew! Well I pick up my motor and 5 speed trans on Tuesday. Here are a couple more pics of the donor vehicle.
  11. slow91fj90

    I have the opputunity to buy a 2002 Turbo Diesel Landcruiser but need some help!

    First off I dont even know if this is in the right section of mud so Ill start where I usually hangout. Okay so I have a friend that's uncle builds vehicles for the US State Department. Well my friend called and asked if he knew anyone that would be interested in a Turbo Diesel Landcruiser...
  12. slow91fj90

    I have the opputunity to buy a 2002 Turbo Diesel Landcruiser but need some help!

    First off I dont even know if this is in the right section of mud so Ill start where I usually hangout. Okay so I have a friend that's uncle builds vehicles for the US State Department. Well my friend called and asked if he knew anyone that would be interested in a Turbo Diesel Landcruiser. My...
  13. slow91fj90

    Truck runs like crap after it rains?

    So this just started the other day. It had been raining all night and was still raining when I got up, I needed to go somewhere and when I started the truck it was missing and stumbling. Just like I had gone through a deep water hole and got the distributor wet. Well I just let it sit till the...
  14. slow91fj90

    Semi float Axle shaft movement?

    Ok so I just replaced my rear pan hard bar/trac bar whatever you want to call it with an adjustable one. Well that's all good but the main reason for doing it was the clunking noise that came from the rear when driving off road or even when I went over a speed bump at an angle. Prior to this I...
  15. slow91fj90

    Rear panhard bar question

    I purchased a adjustable a while back and plan on installing this weekend. For some reason I think I read a thread that said you have to replace the factory bolts, like they can only be torqued once and not re used? Does this sound correct? I don't have an issue with ordering new ones, just want...
  16. slow91fj90

    Only in a Jeep

    Had to share this. I know its not tech, so moderators feel free to move it. YouTube - what a dumbass
  17. slow91fj90

    Entertaining axle rebuild video...

    Saw a link to this site on FB. Looks like there is a ton of videos to watch on this site. I picked this one and it was entertaining. enjoy. 4wd TV Episode 221 - brought to you by 4x4 Earth
  18. slow91fj90

    Fan through the radiator

    Let the :princess: drive the cruiser to work today and she calls when she gets there and says the AT light came on...My first thought is trans overheated, but in 30 degree weather? Umm. This is not gonna be good. So off I went to check it out. I pop the hood and find the fan with clutch attached...
  19. slow91fj90

    Waterhole video

    My friend just sent me a couple videos from a couple months ago from a camping trip out at Big Dogs Offroad park in Gore, VA. After this I decided a snorkel was probably in the works. http://www.youtube.com/watch?v=2ZWRe5Q98I YouTube - camping 070
  20. slow91fj90

    IronMan Snorkel install with pics

    So last night I installed mt IronMan Snorkel. I took some pictures as I went. Overall install went really well. The only problem I had was my template was ripped which caused my holes to be off just a hair. No big deal, just had to make them a little bigger. So first off you have to remove the...
Top Bottom