Recent content by Eisbaer

My Family and I stayed two nights at the Bobby Jo campground in April 2023. Got through the squeeze in Devils Pocket without problems. I knew a LC200 could make it based on Markusons post way back. Made it up SOB hill will minimal slippage. Probably the hardest section I have ever driven -...

If there are others that want to do a half day, then Tahuya it is. Otherwise I am still up for full day in the Ellensburg area. We can try Durr road and see if Umtanum Ridge has snow on top (around 4000ft).

I'm interested. We could do Tahuya or explore one of the wildlife areas such as QUILOMENE or WENUS (north of Naches, south of Ellensburg). Green Dot maps - https://wdfw.wa.gov/about/wdfw-lands/green-dot#print

Any plans on creating a front full replacement bumper with hoops for pre 2016? I don't see a hoop/bull bar version on the website for pre 2016. Thanks, LC200 2014

I did not initially mention the brand, since it appears others have the same design... Heat shield gets removed. Thank you @Taco2Cruiser for the detailed response. I'm very happy with the slids. Bud Built gets free advertising every time I leave the garage. While Taco2Cruiser responded, I...

Hear is my antenna install. I researched if the antenna is tunable or impacted by cable length. Still learning about RF signals. I brought a RG 58 crimper and added a about 5 ft of cable and added a SMA connection so I could take off my roof rack without removing the antenna. In my quick...

I am running Bub Built aluminum. I’ll see if I can fabricate a bracket coming off the skid plate to hold up one side of the OEM heat shield.that covers the plastic actuator. Other side could bolt into the existing holes. Leaving for a 2500mile road trip to Death Valley soon. This is what...

Question for those with aftermarket transfer case skid plates. Is there any concern, that over the long term, the transfer case actuator or yoke of the propeller shaft will be damaged by heat without a heat shield? My aftermarket skids plates, and based on a quick review of other brands...

Does anyone have any pic's of the circuit board/relay placement? I saw Eric Sarjeant installed beside the radiator/battery. Not sure if it fits above the fuse box, or on the new Slee accessory panel.

I do. I'm in Federal Way. I PM'd you. I missed the last get together, but looking forward to twice as many events in 2021. "Hopefully" just a few more months away....

Adding on with a pic of highest road in Oregon. Steens Mountain loop. Getting in a few high altitude pics before we get the LCDC crowd posting the "Don't trust anyone under 10,000 ft" pics. (Which we unfortunately will not be at.) Just completed our 2 week trip. As always the LC is not...

Hope you got it worked out. I have the twin ARB installed on the Slee bracket. Unless you plan to connect an air tank or a remote air connection outside of the engine bay, I think having the switch at the compressor is a great idea. Keeps the wiring simple. Plus every time you use it, you...

Which bluetooth relay and waterproof box did you end up using for the roof lights? Based on the previous posts, I assume you have the relay on the roof to separately control the front and side lights. I noticed the sides had three wires. Did you use a separate curcuit/relay for yellow...

Here is a great link for info on the Washington State Wildlife areas: WA Wildlife Lands or List of all areas It includes the green dot trail maps. I used the Avenza Maps, since Gaia does not appear to support geo referenced pdf maps. As of June 1 dispersed camping is open. I drove into the...

Short notice, but if anyone interested: Events | The Shop OVERLAND Cars & Coffee - Open to Public Sat, November 09 2019 10:00 am - 1:00 pm The Shop is hosting an Overlanding Cars and Coffee with Northwest Overland and TacomaWorld Northwest for all things offroad! Bring out your beasts and...