CC Meeting - November 10, 2011 *NEW LOCATION*

[Granite Grinder]

EBI Cruiser Parts
Unit #105
1650 Broadway Street.
Port Coquitlam, BC
Meeting starts at around 8:00ish

Meet for pub grub prior to the meeting:
Cat & Fiddle Pub
1979 Brown Street
Port Coquitlam, B.C.

 

[kim]

I'll have Backroader magazines for all Four Wheel Drive Association of BC members. If you are not a member, I'll sign you up and give you a mag if you give me 20 bucks.

 

[canucksafari]

I'll have Backroader magazines for all Four Wheel Drive Association of BC members. If you are not a member, I'll sign you up and give you a mag if you give me 20 bucks.

I can't remember when my membership expires. I presume you will bring a list?

 

[kim]

I can't remember when my membership expires. I presume you will bring a list?

I will bring a list.

I will also be happy to collect dues for next year as all memberships expire at years end.

 

[canucksafari]

I will bring a list.

I will also be happy to collect dues for next year as all memberships expire at years end.

I guess it will be a $20 entry fee to get into the club meeting this month.

 

[sailor]

You and me both... Deadbeats are posted in the members section from last month.

 

[Scalp]

Don't miss the thursday cc meeting

 

[Scalp]

Flash! Flash! Bonus attraction at the thursday night meeting...

 

[Yabedude]

I'll have Backroader magazines for all Four Wheel Drive Association of BC members. If you are not a member, I'll sign you up and give you a mag if you give me 20 bucks.

Kim forgot to mention that you will receive 2 collector mags over the year, not only 1. Plus we'll toss in a solid gold dash plaque (you wish ) AND stating for year 2012, a member only annual collector sticker -- when they arrive that is.

 

[AJAEbj42]

Sure, cut into my t-shirt sales...

Seriously, can't wait for the Backroader!!!!!!

 

[BCR4619]

I don't think I will make it.... I kinda broke a part off my engine :/

...but look in the bright side you guys have a better chance of winning a prize! Lol

Sent from my iPhone using IH8MUD

 

[AJAEbj42]

I don't think I will make it.... I kinda broke a part off my engine :/

...but look in the bright side you guys have a better chance of winning a prize! Lol

Sent from my iPhone using IH8MUD

Yes, our odds just went up a whole bunch! Get yer engine fixed!

 

[sailor]

Did you buff it too hard?

 

[kim]

I'm trying to picture 'I kinda broke a part off my engine' and imagine what that could be?

 

[BCR4619]

Did you buff it too hard?

Surprisingly not this time

I'm trying to picture 'I kinda broke a part off my engine' and imagine what that could be?

I was reading the FSM and it said to take off 4 bolts for the Oil Seal Retainer..... I was not paying attention and took off three and started to pry the damn thing off... It has some FIPG on it so I though it was that that was holding it back, then snap..... a corner broke off and stayed on the block with the 4th bolt ...... anywho its with Dr. Voo to get mended lol

 

[kim]

Oh. If you needed a bigger pry bar, you could have asked.

 

[canucksafari]

Don't feel bad Christian. Last year I broke the thermostat housing because I had not checked to see if I had seated the new thermostat properly. Luckily I had the other TD4.2 up on blocks and was able to steal the housing off of it. The new one took about 3 weeks to get here because I was too cheap to pay the Nissan Forklift stealership price. Just another life lesson to check two or three times before using "extra force".

 

[AJAEbj42]

"You can force everything once"

My recent 'oops' was with my water pump, setting the torque wrench incorrectly and 'snap' goes the bolt, fortunately there was enough bolt sticking out after I took the pump back off to double nut it and remove it that way.

 

[sailor]

I did the same thing with a hatch on a boat. Aluminum frame, 24" X 24" square of 1" thick Lexan. Forgot one fastener- crack! Expensive lesson...

 

[AJAEbj42]

Bringing my kids tonight. is out of town. They love cruisers and hate meetings, so this should be fun.