Tech day, help me day...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 13, 2007
Threads
158
Messages
5,471
Location
In the garage.
I am currently swaping in the 3FE into my 60...I may need some help in the next couple of weeks...Anyone interested in a Tech day, help me day @ my shop prior to the RedBird run?
We can work on anyones stuff, I only might need help, I may be done by then, you never know...
Let me know what you all think, It would have to be on Sunday, Cause I work on Saturdays....
 
Give me a day, time, and location. I'll be there. With tools. And beer!!
 
Give me a day, time, and location. I'll be there. With tools. And beer!!

Give me a day, time, and location and I'll be there to drink FineWyns beer!!!:flipoff2:
 
How bout Oct. 4. Or Oct 11 ?
Oct. 4 is my choice
Bring beer if you like, but no drunk drivers leave the shop.
Bring projects if you got one.
 
I got plenty of tools, but bring your own if it makes u happy
I'm in Anderson. 3821 Gun Barn Rd
 
October 4th it is!



Wait, that's 3 hours away... Why in the world would I drive 3 hours one way to help someone else on their junk?!?














Because that's how we roll! :flipoff2:
 
That is how we roll aint it!!!!
 
Ok for all interested...I got the 60 runnin. I do still have the rest of the 62 to strip down.
Bring a project if you got one, help me strip the 62, or whatever If anyone has a wire diagram for a 62 I gould use it to tie up some loose (wire) ends
 
I left my electrical engineering toolbox back in Michigan, but I'm pretty good w/ wiring & electronics. I'll see what I can do to help you out.
 
I'm pretty good w/ wiring & electronics.

Wish I could say that......use him and abuse him Tony!
Wish I could come down and get greezy wit ya, but can't make it.
 
It's ok Gappy...we will all miss you, as far as you know.
Anybody bringin somethin else to work on?
 
Might need to loosen up & readjust the spring stiffeners that I have on the ass end of my Buick, she's riding low in the rear. And my positive battery cable on it needs a lock washer. Other than that, I'm all yours for the day to help out. 3F-E here we come!
 
Good times were had, some mud was smeared on a couple rigs, an exhaust system fixed with bailing wire, and some paint got transferred to a tree (that'll buff right out!) Enjoyed seeing you fellas again, have to do that more often!
 
Good times, Good times... more wheelin than wrenchin...but thats ok too...
 
How did the Buick do in the woods?
 
Where the "F" are the pics?!?!
 
Tony's woods are NOT 80 friendly!:grinpimp::grinpimp: When Ron repaints his rig, I am going to help him work out his two newest dents that I swear were there before I wheeled it. His truck's new nickname is "The Avocado". :lol:

On a more positive note I just back in from the garage and I have finally figured out my TBI issue. I apparently buggered up my fuel pressure regulator when I rebuilt the throttle body, so after replacing it it runs like a champ. I am ready for Redbird now! :bounce:
 
Good news on the TBI issue Clint. Congrats. I am not worried about the dents because I remember you smiling and saying as you were driving that you know where some doors are. That's a relief. ;) Thanks for a good time Tony.
 

Users who are viewing this thread

Back
Top Bottom