Carb troubles.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 26, 2014
Threads
80
Messages
1,412
Location
Tucson, AZ
So my rpms have been high. I’ve tried adjusting the mixture but it only fixes it slightly. I had my cruiser in to Toyota for a checkup and they said my idle was stuck open. Upon checking back at home my idle works fine but I see my drivers side port( or is it barrel?) of my carb is bone dry while the passenger side seems to be working normally.. when I pull the choke the rpms go down a bit. is this normal? Or could that be my problem? I’ve checked my vacuum hoses as I have recently installed city racers brake booster. Everything is fine and anything I was iffy about is replaced. I have an April of 77 with an original carb. Any help is appreciated.
 
Here are some pictures...

39795708-92E5-49C0-919A-341AB7F6DE1E.webp


B99120A7-3C38-48AD-A6AC-9EDDE02CEA8F.webp


BCC53CCD-47DC-4757-8DD0-92FC5A691E69.webp


9094D177-64BA-49F7-959F-8678EE567599.webp
 
So the passenger side appears wet at idle? Can you see fuel spray in that barrel while rig is idleing? If so, and the buttery fly is cracked to far open, try and figure out how to get it barely cracked open. Your solenoid clicks when you turn the key to on, correct?
 
I can see fuel spray in the passenger side at idle. And the idle selonoid clicks when on. What is a buttery fly? I’m a bit new to the finer points of a cab.
 
Butterfly is the round plate that moves when you actuate the throttle. I got the impression the Toyota shops comment "the idle is stuck open" could mean the butterfly isn't closing enough.

I'd pull the solenoid, have someone turn key to on, not start, and see if the solenoid rod retracts. If solenoid does retract, you may have gunk plugging the idle fuel passage. Squirt some carb cleaner and blow it out with air. You can do the test solo by hooking a wire /gator clip to battery+ and touching the solenoids spade. Solenoid will also need to be grounded during test.
 
@JohnnyC thank you! That helps with the wording and where things are. I had adjusted the idle speed. But I was adjusting it lower. Hmm

@thebigredrocker i have already replaced the idle solenoid because the last one failed. (No click) I have been squirting some carb cleaner in an attempt to see is I can shake some things loose.

I may just have to get this torn apart and cleaned..

Also are both sides supposed to be wet? Or just one?
 
Neither side should be wet at idle. At idle, fuel is delivered below the passenger side butterfly plate. IOW idle fuel squirts out a hole in the cast iron carb base, aka "throttle body". So at idle no fuel should be wetting the upper aluminum section of the carb. With the rig running can you shine a light into passenger side and see fuel? You don't want to see fuel up there at idle. If so you need to figure out why.

Could be even though your solenoid is opening, something is plugged up. Have you already blown carb cleaner & air in the solenoid hole? If so, next remove the air mix screw, turn key to on, squirt carb cleaner, then blow air into that hole.

Other possibility is your primary throttle linkage is hanging up somehow, thus causing the primary butterfly to be cracked open to much. It is my understanding this scenario will reduce vacuum beneath the butterfly and fuel can't be sucked from the idle fuel passage.

I'd definitely hook a vacuum gauge and check idle vac number. Believe it should be north of 17 at idle. Needle should be steady, not jumping around. My old F runs at 18ish.
 
Not sure any of this applies to your situation
Pin, Not sure about dribbling out the main nozzle. Usually that is too high float level or a plugged air jet.

But, really rich at idle is a common problem on 75-78 2F carbs. It is often caused by a slightly worn/carboned/bent secondary butterfly that is slightly exposing the secondary idle hole. If the idle hole can see any vacuum at all, it will suck fuel. This is such a problem that in '79 and '80 the secondary slow circuit was eliminated completely. In 1981-87 the fix was to add the "secondary slow cut valve", which provides a secondary (ha!) means of shutting off fuel, just in case the throttle blade is not doing it's job and slamming shut on top of the idle port.
The secondary barrel is leaking. Air & fuel are entering through the 2nd barrel, which renders the primary idle speed and idle mix ineffective.
If the idle screw is not making a difference, then there is fuel getting into the carb at idle, through a different circuit. Probably through the secondary idle port because the secondary butterfly is not quite closing fully.
 
On the back side of the carburetor there are two arms with holes in them. One is on the bellcrank that rotates the primary throttle plate. The other is on the anchor that the linkage pivots off of. There is supposed to be a spring between the two.

Its function is to return the carb to idle.

I do not see that spring in your picture.

I would start there. ;)
 
@65swb45 do you happen to have a picture? I'm definitely interested to see if I'm missing parts!!

Your last pic will suffice. The arm on the carb is directly above the accelerator torque rod coming from the firewall to the carb. The arm on the rod anchor is directly below the "7" embossed on the intake manifold.
 
thank you for clarification @thebigredrocker . also that hose has a BB in it. large enough to seal it. that is the way the truck came. they seem to work. or at least have these few months until my rpm hit the roof. lol.
 
Noticed this line appears open to atmosphere. No idea if it matters, maybe someone will chime in.
View attachment 2152051

Note, that port in the photo above is for a high altitude carb, like mine. Being I'm closer to sea level and the engine is desmogged, mine is capped per Jim C's suggestion.
 
Yup. I watched all 7 BEFORE starting on mine, and again as I worked on it. That Pinhead, he knows stuff.
 
Back
Top Bottom