transfer case

Hey Folks, I just ran over 90k and I started thinking about changing my transfer cases and differentials oils. This also got me thinking about extending the breather on the rear differential. I did it previously on my 4Runner for peace of mind and figured I'd do the same on the GX. The...

I'm headed the diesel way (1HDT) and will be parting out my H55 transmission and FJ62 transfer case. The transfer case is original to the '88 truck. The H55 has ~ 60K. Can you please provide your best estimate on the value of the parts? Thank you......

I have one transfer case shift boot. I miss ordered this thinking it was the one I needed for my truck. It should fit on 1973 and prior trucks with floor shift transfer cases. Part number is 58280-60020 Asking $20 shipped

I have an Orion 4:1 transfer case with an Advance Adapters adapter to a NP435. I do not know the mileage on the transfer case but it shifts well and is amazing to use on the trail. It's a 10 spline unit. I'm asking $1,600 shipped

Noticed this leak after doingthe Freeway Ridge/ Black Gulch trail this past weekend. Is this an easy fix? Should I be overly concerned or can I get by for a while?

Automatic transmission and transfer case for sale. Came out from 1997 Lexus LX 450 with 150k miles. Don't leak oil, shift smoothly.

I am converting a vacuum actuated split transfer case to manual shift and I need a shift fork. Thanks Scott

I have a 1978 FJ 40 with a fairly new (like within the last 15,000 miles) Orion transfer case. It emits a low whine, that builds up as I increase the speed, and then goes down as I slow to a stop. This seems to be a fairly new development, but my 454 big block V8 is so loud, I might only have...

anyone have a line on the linkage and shifter to covert my under-dash transfer case lever to the hump in my '69 fj40? I'm in Portland OR.

I've just noticed a small puddle of oil under my 2002 LX470. Looks like the leak is at the Drain Plug on the Transfer Case. I assume this is the Transfer Case? See photo. In the photo have I identified the fill plug? What oil do I need? I assume I just open the fill plug and pump in some more...

I have a 1996 80 series, 115k miles, lockers. I bought the truck a few months ago and added a OME 2.5'' lift kit with caster correction kit & 1'' Manofre Spacer in front. I had a shop install the lift. immediately after lift install I was getting the GRRRR sound while accelerating/decelerating...

4 speed Transmission mated to 3 speed transfer case --- $250 pick up only located in Bowling Green, KY

I've got a 3 speed case mated to an H41 4 speed trans. I have the shift lever and bracket that mounts to the transmission. I also have the arm that runs down the nose cone. What I need is the linkage parts that run from the arm on top of the transfer case to the shift lever. I think these...

The title really gets the point across about my predicament :laughing::laughing: I've got this FJ62 that I bought for cheap with the intentions of turning it into a DD. For those looking for logic and reason in this thread, you have already passed the point of no return. I have put quite a...

1977 FJ40 4 Speed and Transfer case. Worked when pulled. A little dirty, but should be good for someone elses project. $600 OBO Located in Steamboat Springs, CO

Anybody got a source for a transfer case for an 81 fj40? I'm in Tucson

Needed in Tucson AZ 85750. Would consider tranny/xfer combo. PM please

I'm considering going with an Atlas and am looking for some feedback from Atlas owners. I have a 99 Taco with a D44 front and 4:88's with a stock auto and stock case on 35's (37's might be in the future). I wheel the Rubicon and Moab a lot and have to ride the brakes (disc all around) to make...

I have a 2001 Transfer Case, has 156k miles on it, with wiring harness and gasket kit (04362-60080) will ship anywhere in the continental US. The Transfer case had a leak coming from the front housing and I don't have the time or experience to open up the case and replace the seals and see if...

Specifically, the front output housing - managed to drop mine off the bench, hit the concrete perfectly and took a chunk out of the seal area. Please please PM if you've got parts laying around.