steering

So Cal Very clean, from a 1994. $80 + shipping at cost. Paypal accepted

I just did my mini truck power steering conversion a couple weeks ago and wanted to tell everyone who doesn't have p/s why they should do it now. I've had my Land Cruiser for 5 years now, and if I had to start again, this would be my first mod. I started with brakes, clutch, electrical, etc...

(Ok, Brought my 2003 LC to an Indy to replace valve cover gaskets and tensioner, as the truck (with 165K) was squeeking a bit, and it was time... Got the truck back from him and it now has a hard start problem, and truck loses rpm.s and stalls when coming to a stop. It will also stall...

I just received an order from Olathe Toyota that included my rack, part number 44250-60050 at $545.54. The box has the correct part number on the sticker (no stickers on the part), but cast into the part in a couple of places is the number 60020. Their does seem to be a 44250-60020 rack, but I...

A few days ago I tried to install a new leather on my steering wheel and I was able to do it, several defects in the final product, but the main one that make me do it all over again was the color, it was too light and I wanted some brown darker. I have found my first piece of leather here in...

Is it safe to assume the the tie rod ends and steering relay (sleeved) are the same as a 91 USDM Land cruiser, the shop that was doing my alignment shredded the passenger side on y HDJ81. Toyota wants 357.00 just for the sleeve mins the tie rod ends. I was going to replace all of it with Moog...

Looking to purchase a FZJ80 passenger ABS steering knuckle . Thank you. My zip is 95824.

Like the title says I'm looking for a factory power steering and a/c for my 83' BJ42 3B 24volt. Let me know if you have anything, I need to get some power steering on this rig and I would prefer to go with oem. A/C would be nice also, the weather is warming up in Texas. Thanks in advance

Just need the tube, lower flange attachment and shaft.

Looking for an 82-85 Truck or 4 Runner power steering gearbox for a conversion on my '75 FJ40. Pictured below.

I replaced steering gear with a remanufactured unit. It has taken the slop out of steering completely but the effort is considerably higher than previously. Not sure if it just needs to break in or if there is something wrong. Thoughts?

I removed a couple of bolts on my manual steering box so I could remove the brackets to make it easier to clean and paint the box and brackets. After cleaning, painting and putting it back together I discovered an oil leak around the stud/nut circled in red. To my knowledge, the leak was NOT...

Looking for some assistance!!! I am replacing both ends of my tie rod and of my drag link on my 76 - 40 Series with NAPA parts for that year. The only one not matching up, of coarse, is the tie rod end that connects to my saginaw steering pitman arm. Can someone point me in the right...

No longer have a need for this pump since I don't have my 62. Pump, mounting bracket, pulley and lines = 100 + ship -Victor

Does anyone know a reputable person around Houston, TX who could install power steering in my 83" BJ42? Thanks

Hi all - This is my first real post on the forum after a long time of lurking, admiring, and learning. I purchased a 98 LC a couple months ago with 92k on the clock and admittedly didn't do a thorough enough inspection beforehand. However, the only major issues I have found are blown CV boots...

Would a bad or failing valve create hard, rapid left to right steering at low RPM (think parallel parking)? Recently replaced Timing/Idler/Tensioner pulleys and belts, rack is two years old (not leaking as far as I can tell), and steering is fine otherwise except for slow speed rapid left/right...

In good shape. Some minor ware on th top and sides. Excellent shape for the age. Shipping from 80212, Denver CO.

The paper clip is rusted pretty bad and leaking so the time has come. Going to go with the Derale Dual pass cooler mounted to the frame. This is the model I am going to go with: Amazon.com: Derale 13263 Dual Pass Aluminum Heat Sink Cooler: Automotive I want to eliminate the metal bends on...

does anyone happen to have a 1fz-fe power steering gear they are willing to sell. if so please let me know.