steering

I am getting ready to make some replica power steering pump brackets for the FJ40 Land Cruiser. They will be based off of the original bracket and looks very similar. I wanted to see if anyone would be interested in them. The bracket will be for the 1979 and newer FJ40's that mount to the...

Hi, I searched the forum to find out what typ of steering gear to fit my LC. I have a LJ71 and doing a RHD/LHD conversion and my LHD steeering gear is a little to worn. My LHD steering gear is from an old 1985 LJ70 and if I understand it right there´s no need to rebuild them. Can I use the...

Hi, I'm looking for a p/s pulley (with spacer would be great), the pump bracket and idler pulley for the 3B engine of my 1983 BJ42. Any offers by PM please. regards Jan

looking for a good condition gray steering wheel to replace the goofy aftermarket one that is so popular in Japan. This is for a '91 PZJ70, but I expect many other 70 series would work. Can say for sure that a 60 series wont work and an 80 series wont work.

im rebuilding my 7/72 steering box, but somewhere in the process of dismantling it, getting my wife pregnant, building a house and raising that child to the ripe old age of 2, i've lost the "rear bearing cap packing", (steering box shims and gasket) and the sector plate gasket. i assume i can...

I have a 1978 FJ 40 with a SOA lift and 35" tires. I installed a high steer kit from 4x4 labs, and use a saginaw box with a two piece jointed shaft for power steering. Before the high steer kit, i had a serious case of bump steer. After installation, and the switch to a two piece shaft and new...

So now ive got 324xxx on my hundy and am starting to notice some steering noise in the morning when it is cold and also ive lost some power steering fluid from the resevoir. I have also noticed that the inside of my front two tires is starting to wear down pretty well, given the tires have...

So I have been battling an issue with steering wheel feedback almost the whole life of my ownership. It was even noticeable at stock height. I have almost completely remedied the situation by replacing sway bar bushings, r&r'd the AHC suspension, and this previous weekend replacing the rack &...

So, as the title shows .... I need to replace the rag joint under the steering column just above the floor board. Seems like I can just unbolt a few things and replace the rubber piece that deteriorated ....Or do I need to do anything special ? Etc ..... Thanks in advance !

As the title says, I have a set of used FROR heavy duty steering links for an 80 series. I converted to a Y-link setup last year and these are sitting in the corner of my shop. Some light rust, but the links are strait. If somebody really wants the TRE's that are on them they can have...

SOLD!

Hey I was wondering if anyone knows any threads regarding flushing power steering fluid or if anyone can give me an overview of the process. Thanks

Steering box out of my 1997 Landcruiser fj80 Rather deal local so I don't have to ship (phoenix area, arizona) Got power steering box all parts cleaned and ready to be painted and rebuilt, sector shaft is broken and shouldn't be used. Make me an offer I don't have any ambitious to rebuilt it...

I am looking for a frame plate set, preferably the 4x4labs one. Also looking for the steering shaft, u-joints and pass through/bulkhead joint. I'd also take a pitman arm that can be or is already reamed for 1-ton TRE. Please PM me if you have anything.

Has anyone replaced their TREs (inner and outer), steering rack (the whole rack or just the bush) or ball joints? Would be interested to know but couldn't find any write-ups after doing a search. My tyres have some 3 to 9 o'clock play ..just a small movement..and my steering has a rattle (clunk...

Steering shaft spacer for Land Cruisers (and pickups/4-Runners?) $20 $15 shipped. I don't recall exactly where this came from. The spacer is 1" thick and the diameter of the stud/hole pattern is 2-1/2". SOLD

Hey guys, I'm building a 76 FJ40 with a 5.3L gen 3 vortec, 4l60E, atlas passenger drop, dynatrac high pinion passenger drop dana 60 and a 3 link. Has anyone done a similar build with a SBC, 4L60E and 3 link? I'd love guidance on motor positioning laterally and longitudinally, header selection...

I am looking for the following parts, if you have any of these I would be really grateful if you could send me a PM with your price and the condition of the part. 1. Steering Column Cover 2. Driver´s Seat Belt Gray 3. Steering Wheel, has to be in good shape. Mine is ok but the rubber separated...

My manual steering box has a slight leak. I've been looking around and have found lots on the older boxes including rebuild threads. I was hoping someone out there sold a rebuild kit for it but it doesn't look it. Does anyone know of someone who sells one? Thanks!