replace

Hey guys, so yeah, looks like I've got the radiator crack, so I'm going go ahead and replace it, but I wanted to make sure this is the correct part number for the updated version of the radiator: Toyota 16400-50384, for a 2013 Land Cruiser. I just hit 109,000 miles so from what I'm reading, I...

Replacing leaf spring bushings, The bolts that are on there, bolts look original, very hard to remove. Photo's i've sen they look rough. Should I just just replace with new? Seems like i should have them on hand before I start the process? Are there better options than OEM? (greasable?)...

I've spent the last few hours reading and researching how to replace the rear axle bearings on my GX. Local dealer quoted $2100. Trusted local mechanic quoted $1500 which seems a little high. I'm mechanically inclined, I have access to a friend's shop with a hydraulic lift, tools, press, etc...

I searched - found a few threads about the steering rack replacement which I am not going to venture myself, but not much else about other things to take care of while the truck is under the knife. L side of steering boot started weeping a fair amount of power steering fluid a couple of weeks...

I have a leaking cylinder on my ’71 FJ40. I’ve looked for replacements but not a lot of luck yet. Anyone with some sources would be appreciated. I pulled the wheel off the Cruiser today and it looks like the right side cylinder is leaking ( what do y’all think? ) Is it possible or an option to...

I’m doing a frame up restoration on my first 40, and no surprise, it’s got some rust spots on the driver’s side floor pan. I’m torn between either replacing the floor pan or patching the holes. At what point do you just replace an area with a new panel vs patching? Here’s photos from above...

Hello, Dummy question, but just want to make sure before moving on. I'm ripping out the rear AHC shocks on my 2000 LX470 and on one side this part came off: But on the other side it stayed attached to the frame: To be clear this on the underside of the shock mount. The lower of the two top...

Hello everyone! I'm pretty new here as I just acquired my first 60-series a couple of weeks ago, but I have some questions about the C-Channels on the rig. I'm wondering if I could get away with not replacing them and just de-greasing/metal-prepping/POR-15-ing them, or if they need to be...

I am replacing my front bumper cover and am trying to get the fog lights removed. I noticed that half of the threads and nuts are virtually rust free and the others are horribly rusted. It looks like someone replaced three of the threads and nuts. I have already broken one of the rusty ones...

The tires are 11 years old and suspension 18 years old. I'm FINALLY ready to pull the trigger and change out the suspension. I installed it myself but will be using a shop this time. Current OME kit said 2-1/2" lift and had the castor corrective bushings. A few years later I upgraded to 10.5 x...

Some absolute mother****** threw a ******* brick through my rear vent window. I took out the old window and bought the replacement - popped off the door panel but am stuck - anybody know how to get the new rear vent window back in? Rear passenger side of a 1991 Landcruiser.

I have a 75 and am in replace and repair project to get her running again. I'm looking for side windows that open to improve ventilation. I checked with Spector Off Road and they no longer make the sliding window kit. Does anyone have any idea were I could find sliding windows?

My gas cap key cylinder seems to have snapped, then some plastic things fell out of the side. I could just buy a new cap, but it seems like maybe the metal thing where the cap sticks in is bent. I'm not entirely sure. What should I do? What are my options? If y'all think I should replace...

I have a 2006 TLC. The seat condition is good (and original) but the drivers seatback is leaning inwards / towards the console a bit. Not bad but just enough to notice. I'm 'assuming' it's not the seat frame but a degradation of the seat foam. Any thoughts on causes / option to fix this...

Need some help. I decided to replace the Weber that was on my 86 FJ60 with a Jim C rebuild. Luckily I had all the linkage and choke cable still. I made sure to double check the desmog doc to make sure there is nothing missing before putting the OEM on. Unfortunately, what once was a...

Last year, I got new tires: Yokohama Geolander G015 for our 2000 LandCruiser. The rear passenger side tire has a nail in the inner sidewall & can't be repaired (per Discount Tire) & it has a slow leak (down to 10 PSI about weekly). We have put 16,000 miles (highway pavement) on the truck in...

I have a nearly all-original 1979 FJ40 that I want to keep as close to OEM as possible. It still has the original shocks and springs. What shocks would you recommend if I want to keep it as close to OEM as possible? Also, should I rebuild or replace the springs? If I should rebuild the...

I'm going right through my 400,000km 99 LX470 with 2uz and I'm wondering if the MAF sensor should just be replaced? The vehicle sticks of fuel at idle, like an old carby vehicle with the choke on. A quick good says that cleaning them doesn't quite get them to where they should be. Don't...

95 LC here. I want to replace everything I can, refresh what I can't. Caliper assemblies and the brake lines that attach to them were replaced a few years ago with Centric rebuilds and new Centric lines. Rotors replaced as well. I now have a new booster and master cylinder sitting on a shelf...

Rehabbing front end of my rig. 313k miles. Ran into this when cleaning up PS spindle for new spindle bearing, brass bushing, and seal. Is the ID of the axle tube a critical spec? Thinking of just sanding down those ridges (somehow the axle chattered in the tube at some point??). Have a...