mounting

anyone have the hardware for this that they are willing to let go of?

Finally found a rear air deflector for my LC, only problem is it doesnt come with the mounting hardware. My truck still has the rivnuts, but I need some help getting creative on attaching this to them. Any ideas?

Long awaited, it's finally here. A mounting system that uses a spare tire mount or tire carrier to hold a few extra goodies. The key to this design was to have it adjustable, lightweight, configurable and most importantly simple to take off! NO TOOLS REQUIRED to remove the mount to access your...

Hello, Anybody tried using quick release mounting hardware on a Bowfin rack? Mounting up an Overland Pros 270* (6K). Curious about what system may work.

I just checked Slee's website and saw this piece of gear for the 200-series: https://sleeoffroad.com/products/sok2016/ https://sleeoffroad.com/wp-content/uploads/2020/10/PUB-SOK2016-INSTALLATION-INSTRUCTIONS.pdf --- It's been a couple of months since I last visited Slee's site, but this...

I just installed the Bowfin cruisers rack and we're about to take our first long trip; Colorado and New Mexico. We've got everything set up except how to mount our shovel and axe. Any recommendations? I saw a couple people use the Thule attachments but only for the stock rack so I'm not too sure...

I've seen a lot on here but not on this particular question. First off, I'm a newbie, first build. I've read a bit about designing for shock mounting, locations etc. This basic article was helpful: Everything you wanted to know about Shock Absorbers - 4x4Review Off Road Magazine I realize it...

I face so much creative and helpful content at this forum, so I thought I have to share my modifications on the AHC Reservoir Bracket to convert it to a ARB Compressor Bracket. Please keep in mind, that I deleted my AHC completely and wanted to use that spot for something usefull. Since I have...

So, I got a great deal on an ARB bumper yesterday, but it's missing the hardware and the brackets that mount to the ends of the frame rails. I found the part numbers for the brackets, hardware, etc., but haven't been able to find them for sale anywhere except a 'Mud thread from 2013. I emailed...

To be more specific, what issues would I encounter trying to mount a 65' tub on a 78' chassis/drivetrain. I know the Air conditioning isn't a thing on the 65' model so that would be left out. But as far as body mounts/ drivetrain fitment, what should I keep in mind? any major things that will...

i always seem to get caught up on the frame side bracket for my rear lower links when crawling. Is there a lower profile solution? A way to recess it into the frame? I did find a new bracket but don't think it'll provide any additional clearance. Anyone have any ideas?

I'm looking for the outboard mounting rings, plus springs and screws if anyone has them. My retaining rings seem to be OK, but I'd take those too. As seen in this diagram 81113, etc. RING, SEALED BEAM MOUNTING, NO.1 RH. HEADLAMP (LAND CRUISER (FJ62)) for 1989 TOYOTA LAND CRUISER. #8111390B04...

Hey guys, Just wondering where i can mount a mechanical water temp gauge in my 2F engine. I've had a look around but haven't been able to see anything. I read the manual and it didn't say anything about temp sensors, only the thermostat in the water head. Any help is appreciated. Rohan

I searched a bit. I couldn't find where people are mounting these. IF ballast can set in the space behind the side marker, in the fender, where is a good spot for the relays? Thanks for any help Jerry

STILL working on the NV4500 install. I've run into the classic stumbling blocks along the way here and I'm searching for some alternate mounting solutions for the T-case/ Trans. This project is CRAMPED!!!! All the way from garage space to space in the rig for this friggin humongous trans! Any...

Can we see some pics of where you guys have mounted these inside the wagon? Most of the images are in the "what have you done this week" thread, so the search wasn't too helpful. I am debating to put mine in the cargo hold above the bottle jack storage. Can either insert it flat horizontally...

Wanted: Four Rear Body Mounting Brackets (#1) TEQ part number 51741-60010. New, NOS, Excellent to Very Good Used for summer restoration and installation of a Aqualu 3/4 aluminum tub this summer!

Hoping someone can answer this question. I am working on my revising my rear bumper to hold a 5 pound propane tank for camp cooking. I have a good idea but the way my rear 4x4 labs gas can carrier sits the best solution is to mount the propane tank at a slight angle, like 25 degrees angle...

For Sale - Warn Zeon 8 winch w/ mounting plate (brand new, pulled from a recently sold truck). $900 firm (basically you get the ccot ~$100 mounting plate for free). PM if interested. Located in Knoxville, TN. Nik

I'd like to add an arb compressor twin or single have not made up my mind yet, I tried searching for mounting locations for AHC equipped trucks but I have not comd up with anything. Any help or ideas would be greatly appreciated.