Has anyone been able to source parts, or just complete lock assemblies? My latch stopped working, and it looks like a small plastic piece is the culprit.
Have an Man-A-Fre 4' Old Man EMU lift that I took off of a 86 FJ60 that I recently purchased.
All that is included is the Front/Rear spings, rear anti-inversion shackles, front shackles, and front shackle reversal drop hangers. Front springs will need new bushings. Spring center pins are...
After installing my OME lift kit, my braking performance went from adequate to bad. After installing 255/85/r16 tires, my braking performance went from bad to "holy s*** this is scary dangerous".
Went through the FSM and several threads on mud. After performing some routine diagnostics, I...
I'm planning on installing an H42 4 speed transmission and transfer case behind a 2f in my 1967 FJ45. I recently read a thread where someone did a similar swap into a 1966 FJ45 and had to add a 1" body lift for transmission tunnel clearance. Is a performing a body lift necessary for this...
I know this is a long shot but the PO of this 91 Fj had some sort of lift because he had 35's... The guy was offering me all 4 corners for 80 out the door and I dont want to pass this up but just sorta want to be reassured as to what sort of lift I will get out of it... Thank you!
Im just a noobie that wants to lift his fzj80 and would like some guidance. I would like to do a 3 inch lift as easy as that sound is it actually that easy if I buy the old man emu 3 inch lift kit from amazon or whoever sells them the cheapest? Also I have no clue if I will need to do castor...
The OME lift kit I ordered back in February finally arrived. Everything looks good, except both rear springs have part number CS005RB. I've read elsewhere that the rear springs are side specific and the complete kit should have one rear spring end in A for the driver side and the B spring for...
2003 Land Cruiser, 4.7 4WD, Low Miles @ 85,000, Non AHC (adjustable height control) suspension, Thunder Cloud Gray Metallic Paint in immaculate condition and All Original, Gray Leather in Great shape, Husky floor liners to match, original mats included like new, power telescoping and tilt...
Recently lowered my cruiser due to family growing... all parts have less than 15,000miles on them.
This lift configuration [as pictured] will run 37" tires with 4.25 backspacing with Zero rubbing stock or slight rubbing in the rear fully armored. This will provide a fairly level stance, only a...
Hey, All!
I'm going to be putting an Old Man EMU lift on my 96 Cruiser this summer, so I'm starting to research tires to get a full sense of total cost.
I've been looking at these Pro Comp Xtreme M/T2 Radial Tire. Does anyone have any experience or opinion on these? I'm also curious if...
Hi,
I thought I would put this out there to see if there is a fellow 120'er who would be able to help me install my IronMan lift. I just moved so we could use my garage I also have all the proper tools or I could meet at your place.
I am in Vancouver BC but I also am back and forth to...
Hi Guys,
I'm having a hell of a time figuring out why my front end is clanking and thought I would ask for some Mud' wisdom.
Right before my trip to Baja I installed a new 2.5-inch OME lift with Icon 2.0 shocks. I also ordered swaybar drops and new bushings where the sway bar connects to the...
As I build my budget FJ40 I'm gravitated towards the $500 4" Procomp or Rough Country lifts available when comparing them to the prices for the OME. I understand the reasons to avoid the cheaper alternatives but there has to be another way. I'm also a little confused why one of two people have...
I've been reading all of the pro's and con's of correcting caster with bushings, drop brackets, and plates, and I think for my mild lift (2.5" OME) I'd be better off with the drop brackets in the long run. I'd really like to run plates, but it seems like they're all designed for 4"+ of lift and...
I am new to this site and was wonder if the OME 2.5 lift (heavy) is a straight forward swap ? I have a factory grill guard but am planning on building a steel just wondering if it will be super squirrelly without the Wright I will be running 305/70/16s thank you for any help
I'm having some alignment issues following my OME install. The truck still pulls to the right even after an alignment. It's not terrible but it's definitely noticeable at highway speeds. If I take my hands off the wheel, I'll be in the next lane within a second or two. I took it back to the shop...
like the title says, can you put 295/70/18s on lc200 with 2 inch lift. Say OME? Im thinking about going ironman foam pro tbh. Please any and all inputs would be appreciated. :)
Hi Mudders,
I need some advice on becoming a potential 80 owner. The 96 I am looking at has 179,xxx miles on it, southern state car so no rust, factory lockers, and currently won't start because of a "security light" that is malfunctioning.
Anyone have experience with that? I wish I had more...