help

Hey there cruisers, does any one have a copy of the FSMs for an Fj62. I have an 88 and have a fsm but as I was going through it it appears incomplete. Was wondering if someone could help me out.

I drove about 1,200 miles on a recent road trip. After about 600 miles to the destination I started getting a noise right at 40 mph, with a slight vibration. It starts at 40 and then continues up until highway speed. Constant slight humming, depending on vehicle speed, not RPM. For some...

My 2008 has the footwell leak. My weather-strip fix only worked for a while and I'm finally ready to give in and get the replacement cowl. There are numerous different part numbers quoted in the various posts. Part # 55708-60091 is much cheaper than 55708-60101. I've seen conflicting...

After doing some fuel system work I was driving my LJ78 and it just stopped. Enough fuel. Injectors are dialed in and getting fuel. I don't think that was the issue. So I looked a little more closely. I found that a fusible link was burnt out. The link ran to the glowplug relay (orange arrow)...

Would anyone be able to confirm whether it’s a bearing race driver that OTRAMM is using in his rear locker assembly video at 17:57 into this attached video? I need to safely clamp my locker into the press to torque ring gear bolts, but he calls the item he’s using as a buffer so as not to...

I have a 100 series Land Cruiser. When I start it up it sounds like its fan is running way louder. I suspected it was the catalytic converter and the mechanic confirmed the left was running hot. He suggested I replace them both (of course) but I was thinking about trying a catalytic cleaner...

Okay, my rig has been running at about 1000 rpm since I got it running several years ago. I get terrible milage (around 8 to 10) and have been putting work into it trying to get it up to snuff. I have done several camping and road trips with it and have not had any real issues other than poor...

Hey there I am trying to get this fj45 on the road but currently I have no headlights, all the other lights front and rear work however. The dash light works sometimes when the headlight lever is pulled. The headlights are leds. Also This is wired close to the right headlight no clue what it...

I need help getting the fan and clutch assembly off of my 1980 FJ40. I know it should be dead simple but it will not budge. I have removed the 4 bolts, sprayed it with Kroil (for two days) and used the BFH as best I can. There are not a lot of options on hitting with a hammer. I have tried to...

Howdy all. I visited my folks in Utah over the holiday and noticed my Dad’s LX470 has a bit of rust appearing on the underside of the doors. Similar situation on the tailgate. The underside of the truck looks clean at a glance, likely attributable to weekly washes that include the underside...

Hi All, I recently bought a 2008 GX470 and starting to update some of the hoses. Can anyone tell me what the hoses at the front of the manifold are? Looking for a part# for the right side (starting to crack). I promise I tried to search for the answer before I posted. I borrowed the picture...

Hey folks - looking for help with loading TPMS codes on my 200 series. I swapped the wheelset from my totaled '09 LX onto my new '10 LX and want to get rid of the light. I know the serial numbers for all 5 sensors, just need help loading them. Apparently my Techstream cable is missing the pins...

I’m stumped. I’ve swapped the bulbs and little black inserts between all the dash cluster lights and yet the same slot (upper left) refuses to illuminate. All the bulbs and black thingies (technical term) work in the other slots. I’ve hit each hole w a meter and they’re all getting power...

I’ve searched and searched. In stripping down all the old garbage from PO this is the last thing and I can’t figure it out. Important or part of PO add one? Runs down to front of engine. I’m thinking old fog lights?

Hi there everyone, spanish friends especially! I have found what looks to be an amazing truck and I need help with an inspection and export from Spain to Canada. Is anyone here based in Spain near Madrid? We would pay for your time and help of course:)

Can anyone tell me if this hole should be here? 1981 Need to know if I should reproduce this for the new bed? Thanks in advance

Hi all I’m on the north coast of Cornwall on holiday and I’ve got a burst AHC pipe somewhere, my reservoir is empty Is there anyone out there that could help or recommend a garage not an easy situation at this time of year, not to mention having our dog and wife with me. Thanks in advance

Just bought my first Landcruiser. I am sure this is a dumb question, but I'm asking anyway. I am trying to figure out exactly what I have. It was listed as a 1979 but There are multiple vins/identifiers on the rig. Can anyone help me to figure it out? It was imported from Canada last year...

I have had my 24gal LRA moved from my old 200 to the new one. I did not personally do the install either time so I don't know what the wiring at the tank actually looks like. Here is the diagram from the install instructions: My current issue is that the pump does not run and I do not have...

Hey everyone, I have quite the doozy here as it relates to issues and help I am looking for. I recently installed an Ironman Cell Foam Pro 2in lift kit on my 98 LC100. Since doing so, she is lifted, appears to be quite high. Whenever I cruise over a speed bump at anything more than 7-8mph I...