Good morning big brother to the south!
I am looking to order a full suspension kit from cruiser outfitters but they don't ship palletized items to Canada. My next best option is to ship to MT and then drive down from Calgary AB to pick it up myself. I'll be driving down in my BJ60, so if there...
I'm working on trying to install a new clutch/pressure plate for the 4speed conversion project and I've run into a bit of a roadblock. The clutch is in with the alignment tool and the pressure plate has 3 of the bolts in. However, it is very difficult to try and rotate the flywheel to get...
Me and my dad are going to swap a 12ht into a 1973 fj45 Ute and we don’t have much of an idea on what we’re doing so it would be good if we could get some pointers
We’ve found out that apparently you need a 2h bell housing to fix the angle of the gearbox but we are having a hard time finding...
Dobrý den, jsem tu nový, potřebuji pomoc s Toy Prado J120, pojistka 45 v motorovém prostoru pro ABS/MTR má zkrat, když odpojím konektory od ABS vše ok, nevíte někdo kde problém může být v ABS, děkuji všem za pomoc.
I have a BJ40 that the PO did an engine swap. He had an australian 3B brought in with the following casting numbers: 11411-58010 and s/n 0461711. Can anyone tell me what year this engine is and what it came out of? Trying to get data for parts sourcing.
Looking for help from someone near Brantford Ontario Canada. I need a part picked up at the Brantford Toyota dealer and shipped to me in the US... They won't do it!
Maybe it's available at some other dealer in CA that WILL ship?
Hello everyone, recently experienced the dreaded multitude of ABS lights, alarm, etc. My booster pump was not running. Bought a booster pump with attached accumulator from the local dealership. Install went smoothly. Unfortunately when I turn the key on the pump turns on, runs for 2 seconds, off...
1979 Bj40 with 3B engine. Key will not rotate backwards to “glow” position and glow light does not appear to illuminate. So
1) starting procedure?
2)how to check/change glow light?
3)should glow light come on with the push button?
Thanks for the help!
Note: I know now the prices below are crazy - I'm taking it to another mechanic for a second opinion.
I just got off the phone with my mechanic who is suggesting that my GX is totaled.
Last weekend my motor died and I spent six hours on the side of the freeway waiting for a tow due to a bad...
All,
You may have seen my other thread about the “heater hose” where I had a frozen coolant plug bolt on the head I had to drill out. Good news is I finally got it out today! Bad news is, when I reassembled everything, filled the radiator with water, I noticed the carburetor starting to fill...
Morning everyone,
As you can hopefully see from the pic included, I have the old wheels on my 1981 BJ40. My father in law bought it new in 1981 and we restored it in 2017. It needs some freshening up and I have purchased the chrome covers for the wheels. I’m looking for advice as to where I...
83’ FJ60 fuel injected with Holley Sniper EFI. As of latently she has been stalling out when shifting between gears or at a stop in neutral. Now she idles rough, bouncing down to almost 0 RPM to 1000+ RPM in a loop. Up and down, up and down, on the verge of stalling out. Steering wheel shakes...
Hoping someone can point me to a part number for a 16x8 OEM steel wheel.
I’ve found a similar version that has been posted on the forums, 42601-60600, but this one differs slightly. Photos below. Any help is appreciated!
Hi all, need some technical advise from someone who understands differentials, transfer cases and transmissions on these trucks. I just picked up my first LC200, a 2013 with 100k miles. Super clean truck and I was very very excited.....unitl I discoved this!!
Tires were just upgraded from stock...
I’ve replaced my mystery OME springs (1.75-2”?) with heavy load linear Robinson springs (3”), this netted me about 1.5” lift.
After doing the alignment, my caster is a -1 degree. However, I DO have the OME caster correction kits installed when OME lift was installed by previous owner. From what...
Hi All,
There was a drive line vibration in my truck. Took it to shop to have u-joints changed. No brainer, right? NOPE A NIGHTMARE.....
The shop is unable to get the correct u-joint for the rear drive shaft rear end. Parts store parts do not fit. Any advice? I was going to get a drive...
My brother and I have this youtube channel. Done a lot of car reviews in the past but lately focusing more on offroad/overlanding and gear stuff.
Recent video with my LX and my brother's jeep linked below
Recent facebook threads on ripping out AHC have me wanting to a myths/misconceptions...