front

I found the front drivers wheel bearings had some play. I noticed when I remove the c clip I could move the cv axle radially in the back where it enters the hub and I noticed there is a brass bushing in there. Is there typically a small amount of radial play there or should the cv axle be riding...

I know it's a long shot, but figured it's worth throwing our there... I recently got my 1990 FJ62 up and running, and after only about 2 months someone decided to t-bone me, so my front passenger door is a big crater. Any chance someone on here has a lead on a replacement? There are a couple on...

I dropped off my drive shaft to get new u-joints and rebalanced because it was the cause of my driveline vibration. They were having a hard time finding the correct u-joints and after taking measurements they found that dimensionally these are the same as the factory oe joints that came out of...

Have the attached visually ‘wet’ area on the driveshaft going from the transfer case to the front axle. What could this be caused by and how can it be fixed, if not normal? Nothing dripping and could just be excess grease but just spotted this so not sure if it’s supposed to be that way. ‘15...

I believe this mat came from either a 78 or a 79 FJ40 it was included with a project I recently purchased .It's dirty; I haven't taken the time to clean it at all. It's in good shape- not perfect but pretty decent. Has only one tear I can see that shouldn't be there. I could be wrong on that. I...

I have a set of Escape Gear seat covers for the front two seats only (plus the center console) in grey. These were on a 2015 land cruiser I bought used; the dealer took them off and threw them in the back of the car. I haven't installed them and they've just been sitting getting dust. They...

looks like the standard OME 2" suspension kit (not BP-51) reuses the stock upper perch. so is the unit under tension? I.e. can I disassemble it at home and swap the stock perches to the OME kit and vice versa? Any instructional posts or Vids would be great ! this is for a 2017 if it...

Wondering if anyone has a 2016+ front bumper available, preferably in silver.

Yesterday, I spent the whole day at the mechanic's shop to reseal the front differential. I even provided genuine paper gasket to the mechanic and the mechanic also used silicon, but it still didn't fix the problem. The next morning, there were still tiny drops of oil leaking from the front...

ideally black to match rest of the rig, but open to painting it. Many thanks!

I got this seat mount with some additional parts for my 76 FJ40 and trying to identify what years it will fit. Let me know if you recognize. Thanks

Used is ok as long as it’s in good working order. Ideally one with LED lights and brush bar. I’m In DFW, and willing to travel a few states to pick up. Thanks!

The drivers side door courtesy light is out. Passanger side works fine. Repolaced buld and still not working. Is there a dedicated fuse for this item. I can't find it anywhere. Any help would be greatly appreciated. TIA

Hey Ih8mud community. I recently purchased a ‘99 100 series in Texas. After driving it for a few days I realized both of my top CV boots on the front Axles are leaking. Took it to a shop and they tightened them down just for it to happen a few days later. The boots themselves are new and are not...

Hey Ih8mud community. I recently purchased a ‘99 100 series in Texas. After driving it for a few days I realized both of my top CV boots on the front Axles are leaking. Took it to a shop and they tightened them down just for it to happen a few days later. The boots themselves are new and are not...

Anybody need a patina lens, name your price. Some of them are after market. Or better yet, buy the whole lot cheap😁

Primarily for my full-frontal nerdery. There are a wide variety of spindles used on the 7x Series throughout the range. Most are self-explanatory but it gets a bit weird when you get into the late model stuff that can have ABS or not and/or Dual Mode Auto Locking Hubs (DMALH). Lots of combos...

In need of a peer review/confidence check on my 97' 80. I've got 131k on the clock and did a R&R on the front wheel bearings at 105k. ...So basically these front passenger Koyo's have 26K on them. New spindle was installed at the same time. About 50miles ago, I was getting what I perceived as...

Looking for a clean FJ60 front Bumper! Any one have one or know of one please let me know Thanks

For sale are front and rear Detroit lockers out of my FJ60 (fit other models...). They work great, I switched to ARB so don't need them anymore. I can ship but it will be extra. Frank