For sale are front and rear Detroit lockers out of my FJ60 (fit other models...). They work great, I switched to ARB so don't need them anymore. I can ship but it will be extra.
Frank
Hey guys, I tried searching the forum to no avail but I was hoping to find instructions on how to install the oem front mudguards onto a LX470 I believe I got all the hardware needed, just want to make sure I’m doing it right.
This is my LC100. As you can see, it has plenty of rake. A little bit too much IMO, but a rear bumper will tame that a bit and is included in the 1 tear plan. It rides great, but I am planning on an 12K winch/bumper in the next few weeks. The PO installed 2860 OME springs in the rear, but...
I just came home after being out of town for a month and discovered my garaged 60 has some dings on the fender...the people watching my house are claiming they weren't aware of it or what may have caused it. 🤬😟
Whatever banged into the fender to cause those 4 dings also hit it hard enough to go...
I am at it again.
I was so anxious today that I was changing all those bushes under my car. I expected to get the best experience after the change. Note that I was already having a very good experience, and in fact I should not have bothered to change anything - but there I was.
All rubber...
Hello all!
So a little while back, my drive flanges on the front of my 1993 80 Series had stripped out and caused me to lose power to the front wheels. The splines on the axle shaft had stripped as well and both were showing new levels of polish so they both need to be replaced.
I don't know...
1982 4wd pickup OME lift. What are some common front end issues that you can feel and it doesnt take much movement to make the noise. U bolts are tight bushings are good in the springs and the steering stabilizer. Doesnt look like the torque bar has issues but not ruling it out either. I dont...
I‘m in need of a factory front door speaker. It would be great if it has been refoamed, but ok if it has not. I understand that they aren’t the best in terms of quality, but I need to keep the truck factory in this regard. Please send me a message if you have one you are willing to sell...
I have a brand new eaton e locker for a 100 series that I no longer need. Still new in box with all the hardware. asking 1250. located in Florence Alabama. text for fastest response 2564431923
Thanks!
Okay, so I tried searching, but couldnt even figure the right terms to get close to my problem let alone a solution.
What I have:
2005 GX470 with the Levinson System
What I have done:
Swapped the system for the Teyes CC3
Re-coned both front woofer
Before I ever did the Teyes swap I had no...
Happy New Year! I purchased seat covers from Cruiser Corps which seem great and foam from SOR. I have searched a lot but can't find a good video or picture of where to connect the hog rings for these seats.
Any help is much appreciated!!
1991 FJ80, a while back I had a shop who said they were experienced with Land Cruisers rebuild the front end -- axles, steering knuckles, maybe some other stuff, I don't remember.
The axles they used were aftermarket, they have two outboard grooves for a snap ring, I suppose for different...
I just ordered a set of front doors for the 40. The original doors are rusted out and after attempting a Real Steel patch job, on one (not bad actually), I learned this sort of repair is beyond my expertise, patience, etc. I do have two doors, with patch panels if anyone is interested, I have...
Up for sale is a very low mileage set of Slee 4 inch front lift springs for an 80 Series. I installed them and drove them for about 600 miles. They worked great, but I decided to switch to a set of Dobinson Vt’s. Will ship if buyer pays for shipping. I’m asking $200 obo.
I broke the pedestal on my passenger side turn signal today trying to remove the rusty mounting nut. Anyone have a decent one laying around they're not using? Not concerned about the condition of the lens since I can swap mine over.
Today's carnage...
Selling the old front differential off of my 100 series. Incorrect diagnosis on my part led me to replace the diff. The original diff does not have any issues. Has 170k worth of use, oil had no metal shavings. Can ship at buyers expense. Price is negotiable.
Asking $500