fj45

Lens is built into tailight. I have the one that came out but looks like it is melted / misshapen. It does not have a normal part number. It had a lot of strip caulk around it and seems too small so I am thinking it is not original. My parts book says it should be part # 81270-36010 Anyone...

1978 FJ45 body parts needed. New or good used OK. Need box sides, box floor, patch panels for both doors, inner and outer rockers for both sides, torpedo lateral both sides, patch panels for rear of floor, patch panels for rear cab corners or complete lower back cab panel. Individual parts or...

Updating this post today Jan 25, 2026. Back after a few years wanting to sell my 1977 FJ45 that I’ve owned 18 years. Purchased in Alberta, Canada in 2008 while I was living there. Imported her when I was transferred back to Houston,TX in 2014. These are the things I’ve done since owning her...

I have seen several FJ45’s with good looking 1 piece floor mats… I would think the City Racer mat looks like it would fit but that is only a simple observation…does anyone know of a source for this mat? Rubber or otherwise Thank you in Advance

Hey all, I recently purchased a great pair of reproduction shorty running boards from a skilled cruiserhead in Australia. Since they are hard to get, I brought in an extra pair for efficiency. Available for cost plus shipping within the US. $317 + shipping. Comes with trim screws. Pics from...

Not technically a 45 but close enough and not sure where else to post. 83 hj47 from Nicaragua.

Looking for solid OEM FJ45 SWB removable top. No shipping is necessary. I’ll pick it up. Thank you.

After contemplating and sole searching I decided several months back to take one of our 45’s, a 1966 LPB to be exact to another level. We found the engine and some other components here on mud from another member. This truck was not stock and had been repainted before. Never thought a true...

I have installed the reproduction rear window extrusion for the OEM split window glass as well as all the OEM functioning hardware. if anyone would like a photo of something specific, I can certainly provide them. https://forum.ih8mud.com/threads/az-1964-fj45-swb.1313315/ $48k

Bumper ? For one reason or another a glitch of sorts has taken out your question about the front bumper ? Unfortunately, I couldn’t get back to it.... it went into hyperspace !! Try it again through the ‘conversation’ icon instead ! GroundEater

NOS FJ45 P/U Locks and Keys Set 69500-60070 ( in-dash ignition single side type ) . LINK to Purchase Below ...

Finally got my 45 back home. Starting to dial in some final fixes. As I drive it a bit more, these things are made for people no taller than 4’9”. Is there an option to swap clutch and brake pedals that are lower to the floor, and accommodate longer legs a bit better ?

Did a search and found a few thoughts on this topic but I am still a bit confused. Wiring does this to me lately the original dash panel has been replaced but the ammeter is not doing anything so opening it up reveals the wiring shorted together and I assume, as a bypass. Battery charges at...

I recently removed the defroster vents on my 77 FJ45 so I could clean and inspect the wiper motor. I'm trying to re-install the passenger side vent (LHD) but am having trouble because the wiper linkage is in the way. I tried turning on the wiper to move the linkage to see if that would help but...

No affiliation, just was bored and looked at station wagons, thinking maybe a falcon or something. 8500.00 Been on for 21 days....

NOTE: If one does not want to deal with removing the gussets they could just torch these sections of frame rails and I will disassemble.WTB inner frame gussetts for 64 FJ45. These are riveted into the inside of the frame rails. Need area from steering box to rear of pick up cab. Both sides...

These are riveted into the frame rails. Looking for piece from steering box back to rear of cab on pick up. Both sides. These plates are on-INSIDE of frame and have a series of 2-3 inch holes along the length. Thank you in advance.

Looking for the inner frame gussets for both sides from steering box back to rear of cab on the INSIDE of the frame rails. These are riveted into frame and have a series of 2-3 inch hole spaced out. Good solid condition. Thank you.

Hey folks. I know this is a long shot but in 2018 I sold a 1978 FJ45 with a 3b engine. I saved this truck from the junk yard and was hoping to try to buy it back. I cut out all rust, welded in new metal, and swapped in the 3b. It was one that I never should have sold. Any help would be greatly...

Hey fellas does the 79 HJ 45 H motor have a bleed screw or bolt to bleed the radiator after flushing it.?