fj45

I have seen several FJ45’s with good looking 1 piece floor mats… I would think the City Racer mat looks like it would fit but that is only a simple observation…does anyone know of a source for this mat? Rubber or otherwise Thank you in Advance

Hey all, I recently purchased a great pair of reproduction shorty running boards from a skilled cruiserhead in Australia. Since they are hard to get, I brought in an extra pair for efficiency. Available for cost plus shipping within the US. $317 + shipping. Comes with trim screws. Pics from...

Not technically a 45 but close enough and not sure where else to post. 83 hj47 from Nicaragua.

Looking for solid OEM FJ45 SWB removable top. No shipping is necessary. I’ll pick it up. Thank you.

After contemplating and sole searching I decided several months back to take one of our 45’s, a 1966 LPB to be exact to another level. We found the engine and some other components here on mud from another member. This truck was not stock and had been repainted before. Never thought a true...

I have installed the reproduction rear window extrusion for the OEM split window glass as well as all the OEM functioning hardware. if anyone would like a photo of something specific, I can certainly provide them. https://forum.ih8mud.com/threads/az-1964-fj45-swb.1313315/ $48k

Bumper ? For one reason or another a glitch of sorts has taken out your question about the front bumper ? Unfortunately, I couldn’t get back to it.... it went into hyperspace !! Try it again through the ‘conversation’ icon instead ! GroundEater

NOS FJ45 P/U Locks and Keys Set 69500-60070 ( in-dash ignition single side type ) . LINK to Purchase Below ...

Finally got my 45 back home. Starting to dial in some final fixes. As I drive it a bit more, these things are made for people no taller than 4’9”. Is there an option to swap clutch and brake pedals that are lower to the floor, and accommodate longer legs a bit better ?

Did a search and found a few thoughts on this topic but I am still a bit confused. Wiring does this to me lately the original dash panel has been replaced but the ammeter is not doing anything so opening it up reveals the wiring shorted together and I assume, as a bypass. Battery charges at...

I recently removed the defroster vents on my 77 FJ45 so I could clean and inspect the wiper motor. I'm trying to re-install the passenger side vent (LHD) but am having trouble because the wiper linkage is in the way. I tried turning on the wiper to move the linkage to see if that would help but...

No affiliation, just was bored and looked at station wagons, thinking maybe a falcon or something. 8500.00 Been on for 21 days....

NOTE: If one does not want to deal with removing the gussets they could just torch these sections of frame rails and I will disassemble.WTB inner frame gussetts for 64 FJ45. These are riveted into the inside of the frame rails. Need area from steering box to rear of pick up cab. Both sides...

These are riveted into the frame rails. Looking for piece from steering box back to rear of cab on pick up. Both sides. These plates are on-INSIDE of frame and have a series of 2-3 inch holes along the length. Thank you in advance.

Looking for the inner frame gussets for both sides from steering box back to rear of cab on the INSIDE of the frame rails. These are riveted into frame and have a series of 2-3 inch hole spaced out. Good solid condition. Thank you.

Hey folks. I know this is a long shot but in 2018 I sold a 1978 FJ45 with a 3b engine. I saved this truck from the junk yard and was hoping to try to buy it back. I cut out all rust, welded in new metal, and swapped in the 3b. It was one that I never should have sold. Any help would be greatly...

Hey fellas does the 79 HJ 45 H motor have a bleed screw or bolt to bleed the radiator after flushing it.?

Hi, looking for this switch/indicator for a vacuum transfer case. I believe it is the front drive indicator light switch. Looks like they are not available on SOR.

G’day from Tasmania, Australia Thought I would join and share some pics of my 1/1975 FJ45 seeing as every Google search I do brings me to the forum! What an amazing amount of knowledge here. I’ve been trying to make a deal on this truck since 2019 when I stumbled across the 87yo owner in my...

have a early rearview mirror, has pitting but don't see any pin holes in tin just surface rust. hit with wire wheel to knock off corrosion so you can see the putting. glass is not broke but not in good shape either. arm is in good shape with a little surface rust. all usable just not super...