exhaust

All for a 1965 FJ45. One spring needed (can't believe it did not come in oil filter kit, robbed picture of one below) and 2 exhaust manifold studs manifold side is M12 1.50. I have bolts I can use but would rather have the correct studs. Thanks...

Don’t know if there is any connection, but after having Exhaust put on my ABS and dash lights are in full panic mode. Went to dealer and had codes pulled. Brakes feel great, but I’m conflicted if this is electrical/fuse/computer related or if this is mechanical pump related.

So we purchased the Boss Air Suspension from SloCruisers. We have a Chevy S-10 gas tank in the rear and going to have to reroute the exhaust location to install the air suspension. It looks like the only location is going to be out the side in front of the passengers tire. See attached...

Does someone have a dxf or other CAD file for the exhaust flange on a 1PZ? I'm planning to weld up a new turbo manifold similar to what I've done on my 3B and would ideally start with getting a flange cut on the waterjet.

Selling the exhaust manifold off my 1976 FJ40 Price 145 + Buyer pays shipping

The description says it, selling the manifold off of my FJ60's 2F. It has no cracks, I replaced with 3FE manifolds so don't need it anymore.

Factory or aftermarket is ok; please square port only; 1HDT (12 valve) will not work. I could survive with just the smaller half of the manifold as well if someone has one. Cash in hand! TIA!

Im considering a different turbo, but that would require an adapter to go from the stock manifold to the new turbo, and im not really keen on making a new manifold. It would be about a 10cm extra pipe, i could wrap it in exhaust wrap to prevent heat loss

And i mean like 10mm from it

Hey I have a question for you guys that replaced the 2F FJ60 exhaust manifolds with a 3FE exhaust manifolds Did it change the drive ability around town on the freeway or increased or decrease the low end torque for 4 wheeling did it help with any more power or gas mileage?? Thanks I'm just...

Help me make the wife happy with the 100 series Id like to swap my DT Cat Back exhaust for your stock OEM exhaust. Located in St. Louis

Up for sale is a Magnaflow catback exhaust for 03-23 Lexus GX or 03-09 4runner V8. Asking $450 Shipped

Hey guys, Did the tri mil header install on my 85 fj60, think the machining was definitely worth it so far as it’s all lined up evenly after some shimming and massaging Looks like everything is pretty level, but I’m wondering if it’s torqued enough. I went to 21 ft pounds (within the range...

Hey all, Does anyone know what the torque spec is for the exhaust manifold studs for the 1KZ-TE? I just replaced the studs and the Max Ellery manual only lists the torque specs for the nuts, which is 38 ft Lbs. So far I have only torqued the studs down to 10 Ft Lbs because I’m afraid to go...

Hi! I have a 2001 LC100 with about 165k. 5-10 seconds after start up, especially when the vehicle is cold, I am notice a particularly noxious exhaust smell in the cabin that has a little bit of a diesel exhaust smell (perhaps there is oil pooing in a cylinder as the vehicle sits). It seems to...

I'm looking for advice on what muffler to buy for my FJ40. The motor is a 350 SBC, I'm replacing some poorly installed duals that were low hanging and obnoxiously loud, high school kid's hot rod loud. Today I installed my Walker two into one Y pipe and am spec-ing out everything else I am going...

Hi guys! I've changed my spark plugs, spark plug seals, cap, wires and valve cover gasket yesterday. Engine (1FZ-FE) ran better than ever. But today I got a p0301 code (misfire cilinder 1). Upon further inspection I found fuel leaking from the exhaust gasket at the catalytic converter and fuel...

80 y pipe cat and exhaust from Albuquerque metro to Durango Hesperus area. It’s about 5’ long Thanks!

80 y pipe cat and exhaust from Albuquerque metro to Durango Hesperus area. It’s about 5’ long Thanks!

I have a 7/70 FJ40 that I'm trying to get back to as close to stock as possible. I can get a later 3 piece intake/exhaust that I want to put on my motor. I've seen a few opinions and couldn't come to a clear yes or no. Will the setup below bolt on? Thanks.