engine

Hi all. We recently purchased a very well used, and neglected 75 series ute. I knew it need some serious love, but as it always goes during a build, we certainly got a few surprises along the way. Saying that, it was purchased at the right price with the intent of putting some life back into...

Looking for a 95-97 1fz-fe in the Northeast area. Preferably head gasket already done. Need drop in ready. Any leads would be appreciated. Most likely going this route if I do not fix current motor. Thanks!

As per photo Not locked up, but could use a soaking penantrate Included bracket and hoses $150 shipped lower 48 states

I have all if not most all of the parts needed to small block your fj40-60. 5.7l votrtec, AFI stand alone computer and harness, new flywheel, new clutch pack. Sm465 trans adapter to cruiser 4 speed transfer case. Engine mounts, AA transfer case mount. All parts are brand new or installed and...

Is there a preferred coolant for the 3FE engine? 1991 FJ80, all I know is what's in there now is green and only good to -7F according to the hygrometer. It's clean, I'm thinking if nothing special is necessary for coolant I will drain some out of the radiator, add propylene glycol concentrate...

Vacuum as it pertains to engines and their performance intrigues me. I know enough about vacuum to stumble my way through using it as a diagnostic tool. I’m a data guy because.. data doesn’t lie. Readily available data is best. From my peanut – What is the best approach to monitoring, in real...

Looking for some inspiration for where to mount my winch solenoid in the engine bay and the wire routing. This is for a CBI Front bumper and requires the solenoid to be mounted separately and I would rather not have it in front of the radiator (where it was originally on the truck I got the...

Check engine light on with track off warning. I took it in to a local shop and he said he had to replace the bank 2 cat and quoted $2,800. Didn't really even talk much about the P1605 code. From the research I've done the P1605 code could be the issue causing the P0430 code and the cat might not...

So unfortunately my F motor gave up the ghost today and I am weighing the options of just putting in a 2F or going the full montey and going to the 2FE with an h42 5 speed and transfer case. would i need to change the drive shaft lengths in order to do this. also what other fabrication would I...

Hello. I have a 1983 HJ60 with the 2H engine and lately i noticed that it is loosing coolant, at first i thought that it might be because of air in the system since i did a flush not to long ago. A couple of days ago it decided to suck the expansion tank dry during a 15 minute drive, so i...

Hi All, New to working on my cruiser. Started it up yesterday to let it warm up in the Utah winter and started hearing this clicking/rubbing noise while idling from the fan area. It seemed to go in and out, so I didn't think much of it. Drove it a few miles down the road and didn't hear the...

$40 shipped

$250 plus shipping. No inspection cover. I may have an inspection cover, I have to look, and if I do I can include it for $100 extra

2004 LX470 randomly hard to start when engine is warm. Changed the fuel filter, spark plugs and ignition coils with no change. No dash lights or codes. Any idea where I should go from here? TIA

I am needing the engine wiring harness for a 1991 landcruiser from the ECM to the injectors and all the other sensors looking for as complete as possible. Let me know what you want shipped to utah 84010. PM or email me at stielow775@hotmail.com Thanks so much Matt

So, my engine mounts are shot. My car is a G spec 200 with a 1VD and manual box. Bare bones, UN spec, but it seems this bring some challenges. The engine mounts on my car are oil filled but have no vacuum tubing. These mounts are only specifically fitted to my spec of vehicle, which is rare...

I have a 4 speed trans from a 1984. Bought the trans/transfer combo but don't need the trans. Turns by hand and I can get additional photos of the inside. $350 plus shipping cost. (Runs around $200) Thanks.

15

New to the forum. New to the Brits, so ignorant on them. I'm helping my son with a 1993 110 build. He is thinking going with the BMW n54 & the 8HP45 trans. Me personally, no fan of BMW due to $$$. Reading on here with some of the n45 engines, sounds like issues. I'd rather do a 6.0 LS engine due...

$80 Shipped CONUS