engine

Alright... don't flame me too bad for these questions. I found lots of info on engine oil via search engines and this forum, yet I could not find an answer to my specific questions. I'm trying to decide on a synthetic engine oil and viscosity for my 1HD-FT. I am a huge fan of Mobil 1...

Hey folks, I've been hearing about this forum for years from my brother - not sure what took me so long to visit! I've got a dead Tacoma on my hands in Richmond, VA and hoping someone has some ideas for me. It's a 2004 PreRunner, and only had 165k miles on it before it was killed by a...

I've been having an issue over the last week that first started when I was out camping. I had my cruiser idling to charge our phones while at camp on friday and the engine sputtered and died. No CEL or anything. It started up again and idled smooth, didn't have the issue again until this...

so thinking unless im wrong its cheaper to rebuild my existing fj60 engine. it runs but 1st cyl is low comp and leakdown shows leak into oil fill. can anyone recommend a machine shop or engine rebuilder that knows about 2f's in socal az or nevada? would love to go with a high performance mosley...

I have a scary klanking sound can mng from my motor. I replaced my thermostat last week and everything was fine. Now today, I here a clank, clank, clank coming from the motor. My son was helping me and, when we were putting the housing back on, he dropped the socket. We couldn't find it right...

1993 Toyota 1KZT-E engine, trans, transfer case out of a KZN130 Hilux Surf. Motor has 69k miles. The motor compression tested 450-455psi each cylinder. EGR appears to be intact. Marketplace video and listing This surf tipped on its side, and I acquired it from the owner at the time. I pulled...

LX470 Engine Noise As the title states, can anyone easily identify the problem with the noise? I tried turning the fan by hand with the belt still on and it moves smooth as butter. I have no idea where to really start.

I have a 3.4 v6 engine and Auto trans which I removed out of a rotten frame Tacoma. was run and drive truck with 89k miles.

Hi I want to know if this is an 1F, or a 1.5F or a 2f block? Certainly the head gasket is 2f I believe. Can some one help me?

I'm getting close to starting my rebuilt F 145 for the first time. The head was resurfaced with new valves and the cam was reground by Delta in Tacoma, WA, plus reground crank new bearing, rings, etc. I'm wondering what I should set my valves at cold before starting so that when I break in the...

Can anyone tell me what this part is or does? Its located in the front left of the engine bay and seems to have vacuum hoses connected to it

I have a good running fj60 2f with 215k on it. It’s being sold as a long block at $2500. If you want additional parts or the entire motor please let me know and we can talk pricing. Compression number are the following. 1-140 2-120 3-150 4-150 5-150 6-145

I am hearing an engine knock when I start the LC. After the engine warms up, it goes away. Over the last 5 months the knock has gotten slightly more dominate. Someone told me that I can drop the oil pan and take some measurements on the bearings then order the races oversized to remove any...

Good afternoon. Currently trying to start up an engine that has been sitting for a little bit but there's no fuel leaving the pump. It's getting to the circled screw and no further. Any ideas?

Afternoon. Recently I put a new (to me) 3B into my vehicle. Today after bleeding the clutch and tighting off the bleeding valve the pedal has gone solid and doesn't disengage the clutch when the pedal is pushed in

1979 bj 40 with Aussie 3B engine. Are BJ and FJ dipsticks the same? Having a hard time finding a replacement for the 3B

These are not yet pulled, but will be in late March / April and thought I might test the waters to see if there is any interest in them. The engine is a 1FZ-FE out of a LX450 swapped into a 97 Land Cruiser about 16 years ago. Mileage on the engine is at least 180k, but likely much more. Of...

Complete good running diesel engine $3000 plus ship. jodtan@yahoo.com

Hi all is it possible to remove the engine oil sump of the 1kzte while in the KZJ78, I was going to inspect and clean the oil pickup?

1987 FJ60 Complete Motor, transmission and transfer case(except drive shafts) on Frame. 307000 miles on well maintained motor. I am using the body for an LS3/80 Series Frame swap. Price: $3000 you can contact me (LYLE) at (ultracyclist@yahoo.com or text at 215-280-27450) links for complete video...