engine

I'm looking for a 1KZ-TE engine hoist hook or lift hook as it may be referred too. I have not been able to find the part number but this is the front one and I need a replacement as mine clearly uh yeah. Changing motor mounts out and it gave up the ghost.

As my title says, my engine is total loss (230000 mile vvti 2006). I was driving at the highway doing 50mph when my car started shaking and stuttering. Pulled the car aside and waited for roadside help (Germany). They started it and it sounded horrible so quickly turned off and pulled out the...

1979 2F engine, D smogged, 91,000 miles, in the middle of replacing valve stem seals, and the replacement seals do not match the original seals on the engine. Been getting white smoke on start up that seems to reduce as temperature of engine reaches normal. More white smoke while driving down...

Working very well from an engine I sold. $250 firm on air flow meter. It has not been tampered with. Intake hoses, send message for all 3 parts or each separate part. Shipping for air flow meter is $16 or less.

Hey there, It’s been a minute or two. I’m looking to over haul my truck. I really don’t drive it but I’d like to keep it and bring it back. Its runs but engine leaks oil. It runs fine . I need new brakes and rotors, probably times for suspension to be re-worked . Exhaust was completely changed...

So, I've been absentee from club events for, well... Ever... due to running our company and working too many hours. Still have my 95 80 series and about 6 months ago had a pretty decent head gasket failure. Long story short, my 17 year old daughter totaled my work truck and my cruiser became...

This is going to be tricky because it is an audible clue. I've finally had a chance to do as much deferred maintenance as I'd hoped to and got the 80 out for a long drive and some trails. I have a sound that I can't diagnose, and am wondering if I could get some thoughts from the group? I...

I have two heads: 60051 (1974) and 61031 (1977) I have read many threads here, but not many really had comparisons between F.5 and F2 heads. Especially with the pictures. I try my best to summarize some information here. All my measurements are not 100% accurate, but give some idea of the size...

Looking for a complete 2F carb for a 84 FJ60. Have a serviceable one running currently but would like to pick up another one to do a rebuild without taking the truck out of commission for too long.

I have a 1997 4.5 liter in-line 6 cylinder engine block that I want to give to someone who will use it. It had 44,491 miles on it when it was replaced. It was replaced due to lack of oil changes. It had a lower engine knock. The block is absolutely rebuildable. It is located in Tyler, Texas...

My 1984 fj60 tends to run pretty low oil pressure when its hot outside. In the cooler months and in the mornings it reads just fine. What could cause the low pressure readings when its hot out?

I need a fj60 TC. Thanks all.

I am looking for a mechanic for my 3B in my land cruiser BJ40 It seems to be running fine but I suspect it I should preventatively replace the head gasket and peak at the pre-cups ideally I would just like to refresh or rebuild the engine I havent found a master list for diesel mechanics by...

Hey all, I know this has been debating And argued and beat dead a million times but I’m here to bring it back up and hopefully some local dudes will have some input granted our climate is so “extreme” during these months. For context truck is a 1fz-fe 326k. Full coolant flush, fresh radiator...

Looking to sell entire drivetrain together if possible, but will consider selling individual components. Engine is in good running condition and can post pics and video of vehicle running here shortly. Vehicle mileage is unknown. I've put less about 5k miles on it in the last 15 years but I'm...

Introduction Greetings 👋 I am starting this thread to share information, ask questions, and generally document my 2RZ engine swap into the 1984 Toyota Pickup that I bought last year. I had some trouble finding recent information about this swap, so hopefully this will help others who arrive...

Both removed from running 60s during engine conversions. Worked when removed. 1 needs a shim washer added to the clutch. Original denso $40 each?

I suspect these two bolts may be the source of small annoying oil leak. Can someone tell me the purpose of these two bolts and if there is some type of O ring or sealant needed here? The blue oval are the two bolts.

My '03 LX470 with 190K miles experienced the infamous heater tee failure and overheated. With the system repaired I now have an engine that runs beautifully but consumes coolant. As a hail-mary I tried K-Seal, to no avail, so it's time to fish or cut bait. I figure that I"m looking at $2,500 -...

So I was going through old videos and I've just noticed ever since the rebuild and injection pump change, my engine has gone from sounding like a typical diesel to more of a VW TDI sound. Before: After: