engine

Got a brake booster that I bought from a mud member a few years ago. During my engine swap I upgraded the booster to a PDI one so I no.longer need this one. Diaphragm is in great shape, supple with no sign of tearing. Check valve is good too, replaced with a new one 20k ago. $150 buyer pays...

Me again. One of the three people that post in this forum. I’ve noticed a sucking/whistling noise on acceleration. It sounds like it’s from the left side of the engine I can’t tell if it’s a boost leak, I don’t think it is. I think it’s intake noise if that makes sense. I can’t make it do it...

I've got a LX470 with 322K miles. It's recently started intermittently loosing power, typically, when towing my 5500lb travel trailer uphill. This only happens very intermittently (and momentarily) and no check-engine light is displayed (no codes are logged). Engine never completely dies. I can...

Hello, I am selling my 1997 1FZ-FE engine with its transmission. The engine and tranny have 267K mile sand the head gasket was done at 239k. I am selling the engine because I have swapped in a diesel. The 1FZ-FE engine was fully repaired along with some nice add ons such as honed throttle body...

(Toypta 3b)When I go to turn the key I can't hear fuel pump (like I usually can) and the engine is reluctant to start and will stop if im not giving any throttle. I tried to take the fuel filter thing off but am not sure how to take it off. Any ideas on either? Cheers

Brand new, in original packaging. Engine Wiring Harness for 1FZFE. Part No. 82121-60343. Please verify it works for your application. Accidentally purchased 2 of these. Was purchased a year ago and has been stored since. I don’t really see a use for it anytime soon. SOLD. I will accept...

Hey All, I previously had a 94 that I loved but totaled it on the way to deer camp a few years back. Been in a Tacoma since, but came upon a 92 near me that i am going to try to buy. I worked on the 94 enough to be pretty familiar with it. Are there major differences between the two years...

I just pulled the carb off of my running FJ60. It ran okay, but could probably use a cleaning. It has a new float needle and the bowl was cleaned, but it could still use some clean up. The throttle linkage that is attached in the photo is no longer attached. $175 plus shipping

I have a working smog pump from my 87 FJ60. It operates like it should and looks okay. $125 plus shipping

Hey guys, currently restoring a 1981 hj47 and I’ve been chasing a little engine drama for awhile and can’t quite seem to fix it. The Ute I bought has had a couple restore attempts so not sure what’s been done engine wise, it’s blowing a decent amount of white smoke on acceleration and a small...

I picked up this rust free LX earlier this summer. No engine but I have a few spare 1FZs around to rebuild. Same for the original 343 auto. Interested in what you 80-series enthusiasts think the direction should be. This Cruiser will be for sale once finished. Rebuild a 1FZ and run a good...

This came with my 65 fj45 which now has a 2uz in it, so this won’t do me any good. Original engine hand crank for a 1f. Asking $100 plus shipping. Located in Northern New Mexico. I will add picture’s shortly

Aisin carb from a ‘75. Just a rebuildable core, but I think it’s all there (someone please correct me on that if that’s incorrect). Located in southern middle TN. $75, obo, plus shipping. I have never used this carb, it was just in boxes of parts that came with my 40 when I bought it years ago...

I seem to have lost several parts to my F engine. I need parts 13, 14, 60, 16, and 18 for a '69 F engine in the pic of the crank and the 3 timing plate screws that is part 75 in the timing pic. Most of these parts are the same for the F and 2F. Anyone have anything? Cheers, Mike

There is a loose wire attached to the engine block near the alternator . Any ideas where the other end should be attached? Thanks!

Brand new, never used 1992-1996 land cruiser 80 series radiator, 3 core brass. I am willing to let it go for $100. I do not have time to ship it so local interest only, if you are willing to pick it up.

friends and colleagues, I finally got my turbo installed on my 78 BJ40 3B (from a 1981 BJ60) and had it running well when my engine seized during shut down a couple days ago. We’re going to pull the oil pan soon to discern whether there may be a simple fix, but if there isn’t, I am very...

Has anyone had any luck permanently disabling the evap canister sensor on their 200? I am in the process of fixing all the issues with my truck before selling it, and this is the last thing I am down to. Trying to determine if there is an easy way to fix engine code it throws (which prevents...

I heard an unusual noise in my 13B engine that started relatively suddenly. It does have an after market turbo…if that matters. I pulled the valve cover and found these unattached laying freely inside. What are they? Thanks

It worked well last I ran it in 2016. Has been stored indoors, boxed up. P/N 89661-60170 $65 shipped