engine

Toyota FJ40 Valve Cover F engine (8/71). Comes with brand new Valve Cover Gasket (1) and Stud Seals (4). The cover was sandblasted (outside only) and painted with rusto black primer. Underside retains the factory black coating. Gasket and seals are same as 030-06A, Cover is same as 050-37 from...

It has 267k miles on it and was a good runner when I removed it. We can arrange delivery or meeting you half way if you are not more than 100 miles from me for extra cash. $200 OBO plus shipping

1989 with 65K miles and a 1990 with 233K miles (currently fully operational)

I recently replaced my engine and had all new filters and belts replaced. When driving with my main fuel tank selected, it sputters on acceleration. When I switch to my sub tank, it runs just fine. I am looking for suggestions on where to begin looking. I am not a mechanic but grew up tinkering...

Hello, this A442f was in a 1994 FZJ80 I had for a couple years until I rolled that truck in Dec of 2015. I don’t know the year or the miles on the trans bc it was a wrecking yard replacement from before I bought that 1994 80 series. It was operating very well when I removed it. I have...

Apparently, I am in need of the elusive and discontinued wiring harness for my 94LC. Long story short, I was informed from my mechanic the harness suffered significant and unrepairable rodent damage. Mind you I am not knowledgeable on mechanic work. Basically, I am on a knowledge hunt, to see if...

Lights are flashing. VCS engine and 4lo. Car runs fine. Never seen this. Thanks - Joe! ***it resolved itself for now - no more lights*** Must have reset the system as I had multiple trips today. :) Yay!

Yesterday after a short spin, my truck started to overheat. It went from normal temps to 280+ according to the Scangauge. I was able to get it home, I'm sure I should have just stopped driving when it happened, but I was close and there were other things going on at the time, which led me to...

Selling this distributor came from a running 87 FJ60. $125 plus shipping. Best to email me shmukter@pa.metrocast.net

Hi, I have an 01 LC and need the subframe crossmember that the tranny sits on. Part No.: 51204-60150CROSSMEMBER SUB-ASSY Anyone have a used one without rust? Thanks I’m in NH (now).

Long time lurker here, first time posting. I've been reading countless of posts with others with overheating engines but I decided to throw mine into the mix... Back Story: I have a 1996 land cruiser, IFZE-FE, with almost 256,000 miles now. My dad bought it 13 years ago and I started driving...

Used but good working MAF from 1988 FJ62. $100 plus the ride from 49459.

I have an f engine from a 1969 fj40 that has less than 15 hours and less than 25 miles on it since a rebuild. the rebuild yielded a crack around the number three cylinder. the head has new hardened valve seats. the block has been bored 30 over new pistons and rings. the block has a reconditioned...

Regular oil replace … grabbed the wrong box … 3.5 quarts of ATF into the engine before spotting the label wasn’t what it should be … immediately drained and filled new oil filter removed … assuming as far as eff-ups go, this is pretty low on the severity scale (hoping). How many flushes of new...

In the earliest of stages to do an LS swap on my 92 LC. Priced around FB Marketplace for a donor engine, and figured I’d give Mud a shot too. Let me hear what you got.

hi mud, I could use some advice. 07 LX470, 190k. I've had the truck for 3 years and 20k miles. No major issues until a few weeks ago. Was driving over a mountain pass and noticed that when I accelerated, there was a high pitched whistle from engine bay. Letting off the gas slightly caused the...

I have couple of 24V relays for sale. Pls inbox if interested. Part numbers are 28610-54180 24V 81980-25050 24V 28300-56010 24V 28590-57020 24V 28590-56070 24V 28521-68130 12V 28521-57010 24V.

Hello everyone, sometimes my Bj70 (3b engine - 1985) remains accelerated, it doesn't happen often when cold, it happens more times when hot... I've already checked the accelerator cable, it's in place, it seems to flow well, new pump diaphragm, new injectors... I can't figure it out, it happens...

Anyone have an idea of what’s causing this noise? It gets louder and higher when I hit the gas. It’s intermittent though and never happens whenever I’ve brought it in for service. If anyone recognizes it let me know so I can tell them next time I bring it in...

We have the opportunity to bring relatively low kilometers 15B-FT engines to the U.S. These are perfect engines for anything where a 3B, 13BT (or any B series engine) used to be, without modifying engine mounts, changing transmission or transmission position. These engines come out of Coaster...