My A343F is cooked. Where can I get another in the US that will bolt up to my engine? I see amayama has a few but is there a source here, like a JDM junkyard or parts warehouse? Anyone had this dilemma?
Guys I’m hoping someone might have an engine stand they aren’t using they’d be willing to loan out for a few months. I’d like this project to be wrapped up by thanks giving but I may need to dip into early December looking at the project honestly.
I can buy one for sure it’s just one more...
Another weekend in the silt, sand, and dirt, another air filter.
I normally use Toyota OEM air filters, but this name brand low cost alternative caught my eye. Bosch is the other major OEM supplier on par with Denso for Toyota vehicles. Denso is who makes the OEM Toyota filter. With as often...
Guys I just got a 1976 FJ40 and need some help decoding the block and head numbers? The block does not have a vin number stamped but is stamped "2F" casting 1141161013 and the head is casting number 61050. The pistons are domed
Data plate - model - FJ40LV-KCJA The engine - 2F
Any help you...
Looking at FJ40's lately. Been scrolling through the build and tech threads to try to gain some knowledge. Just in the last month, reading through some threads, I'm already noticing things on some online listings which I had no idea about before I found this site.
My price point is pretty...
I went out to my car today to fired up, and got a “check AHC system” message, and a dead battery. Once I started taking away the engine, cover to get a jumpstart, I noticed that there was residue on engine components, and an indication that it was coming from the top seal of the radiator...
Rebuilt A442F from my 93 FZJ80 for sale. All new clutches, new converter. It was rebuilt by my local transmission shop about a year ago. But never installed. Just needs a new breather for the top of the case. Central Ohio. When I get my truck fixed I will drive to state line for asking price...
Fairly novice at these kinds of things. Recently got my hands on an 83 BJ land cruiser (Toyotas 3B Diesel engine). Got it for a good price so i new it’d come with baggage. Test drive was uneventful so I said why not and was buying from a mechanic. Been driving it around as my daily for the past...
I have a factory non-EGR 1FZ-FE and H151 available from my Saudi spec 80 series. The truck is a 1996 model.
NOTE: Transfer case is NOT included in the sale, I'm keeping it for my conversion.
Both the H151 and the 1FZ had been rebuilt by previous owner.
1FZ Compression (test was done after...
Good afternoon ladies and gentlemen,
I am the proud owner of a 1984 HJ60 equipped with a 2H engine. As many of you might be aware, it's on the slower side. However, I plan on making this my lifelong car and envision undertaking a full restoration to transform it into a ski-van/doomsday vehicle...
So I want to mount some onboard air in my engine bay. I plan to remove the carb cooling fan and use the 4 unused bolts in the pic. Couple questions:
1. To remove the fan there is one bolt under the mechanism that helps the hood raise up. Any tips on removal...seems like I would be unbolting...
210k miles, runs great, burns about 1qt every 2k miles, could use valve seals to fix that, 1500 takes it, prefer pickup but may be willing to ship! Came out of 96 lx450, pulled for upgrade
Hey guys was just thinking maybe it’s time I start a thread for 1fz-fe I have been rebuilding and selling them for a while now and figured I should start documenting it in a thread. I usually buy motors from trucks with a blown head gasket, but sometimes buy whole trucks and rebuild them and...
Looking for a decent crankshaft. Going to be getting machined so condition not a concern as long as it hasn’t spun a bearing too bad and isn’t super rusty on seal surface.
Also if someone has a junk crankshaft please reach out as well as I have uses for that too.
Good running engine, 210k miles, valve seals a bit dry, burned 1 qt of oil every 2000 miles, ran great when pulled for upgrade $1500 takes it, prefer pickup but may be willing to ship