carburetor

Brand new. Was on my project truck, but never fired up. It's a kit with the pedal, air filter adapter, cables. Asking $350. I'll be at Round Up next week and can take it with me. Weber Carburetor Conversion Kits for F/2F Land Cruiser - Man-A-Fre

83 fj60 carb internal spring. Seeing where i can find one

Early F135 in Kentucky for Sale Including Big Window Carb (damaged at base) :frown: located in Bowling Green, KY

Ok I am finally breaking down as I really want to figure this out. This time last year when I rebuilt my topend I also rebuilt the carb. Since then I have had an on-going issue with tuning the carb so that it will HAPPILY idle below 1k rpm. Used the proper kit from Kurt at Cruiser Outfitters...

Carburetor off 03/76 2F. Stock Aisin carb that was rebuilt last summer. Has only been ran a small amount till I diagnosed my 2F has the back cylinder knocking. Cruiser has less that 72k miles on it. $100 plus shipping.

Hey guys, I'm swapping out my Weber for a Trollhole carb and I need a carb insulator. It's a Jan. '76 2F motor. Let me know if anyone has one. Thanks, Darren

As stated in the topic I'm in need of the throttle linkage used for the cable to the carb... in need of everything Shipping to Florida

I checked out a local machine shop this afternoon about drilling a vacuum port for distributor vacuum advance. The set-up time would cost more than the actual drilling, and would be cost prohibitive. I could probably do the work myself, but don't have a drill press, and the bit (0.020" to...

I am currently in the process of rebuilding two 2F Aisan Carburetors. One was stamped 5J27 (1975 October 27) and the other 6B3 (1976 February 3). The one built in October 1975 was the original carb for the 2F in the 1976 FJ40, never been rebuilt. The second one (February 1976) I purchased a...

I am looking for somewhere to buy the individual gaskets for a Aisan Carb. I do not need a full rebuild kit as I have recently rebuilt my carb. However the gasket that fits between the carb body and top has been torn. I would like to know if there is a place that sells that gaskets individually...

Hey Guys. Aside from my fuel lines running into and out of the carb do you have any ideas as to what would cause these drips on the front of the carb facing the radiator? I had this rebuilt a few years ago and it runs really really well. But I didn't do the rebuild and carbs are new to me...

Can someone please identify this Carb ? It's on my 55 (1972) F engine. Thanks Mike

My carb is in the middle of a rebuild and is missing the correct metering rod. Does anyone have a spare pre 1964 Asian SD40 1 barrel carb metering rod that they don't need? Thanks

I have a stock carb from an '86 2F for sale. It was rebuilt by the previous owner of the engine, and it could use some fine tuning. I removed it to replace it with a desmogged version. Asking $200 shipped

I have a 62 SD40 in need of a metering rod to finish a rebuild. Let me know if anyone has a spare. Thanks

I could not leave well enough alone and tried to remove the screws holding the butterfly to the shaft. I was able to get them out and might even have enough threads left to put new ones back in. But these screws were staked into the shaft, so does anyone know how to reinstall these screws the...

Wanted good not broken carburetor insulator shield for a FJ60 1984 2f. Shipping to Southern California. Maybe I needed to say that I don't want to pay the $125.00 for a new one from Toyota. Thanks, Robert

Running a 1970 (11/69) stock F engine and am going to a Trollhole carb. The new carb only has one vacuum port compared to the three I had before. I also have a vacuum retard distributor with petronix. The FSM (1972 F egnine) actually shows a Vac advance dizzy (page 8-25 or 160 in the pdf.)...

I had the carb on my 1982 Toyota rebuilt due to not starting unless I hit it with ether after sitting for a day, but the issue I'm having now is when I give it gas under a load it will give that sucking sound and have no power at all when trying to drive the vehicle in gear unless I really goose...

In the process of desmog and rebuilding the manifold and gaskets. Figured I'd post some picture of my carb was rebuilt by @OTRAMM 2 years ago. Would like to know if anyone sees something out of the ordinary or needs adjustment or replaced while I'm putting it all back together. Any help is...