carburetor

Hey there. Reading up on adjusting my carburetor, the Carb 101 basics section here discusses using a vacuum gauge to determine the lean drop-off point. My question: where do you hook this vacuum gauge up? Pictures would be most helpful, but I'll take anything. Thanks! -Calvin

$500. Not interested in shipping. This 2F came out of FJ60 that got parted. I was told by the owner that the engine had a rebuild ~30k ago by a mechanic at worked at Land cruiser connection/4x4 connection in VA. The odometer was at ~220k when it was pulled. I have no proof of the rebuild...

Hello, I have the following for sale, prices do not include shipping. 1980 FJ60 Parts Manifold Set - $200 OEM Carb - $100 Air Rail - Less than 300 miles - $200 Smog Hoses - $25 each Chrome hubcap set - $100 shift knob - $10 Shift fork and new throw out bearing - $75 New Clutch plate - $40...

what is this thing below the carb thats seems to be connected to the fuel cut solenoid (green thing i think) could it be causeing my idle issues

hey guys just a few days ago my smog pump seized and i couldnt get the idler pulley so i devained my pump. i had to cut one of the large hoses on the back of the pump and just put tape over the openings. but now im coming across a idle issue when i start it. i have the gasket leak where it makes...

Hey everybody. Just joined the world of 60s a couple months ago, and now I'm finally digging into the engine bay to get familiarized and to tidy up some of the PO's work. It's been desmogged (at the top of the list of things to double check) and has some aftermarket carburetor that I need some...

hey everyone, I have an 85 fj60 with a bit of a carburetor problem. Nothing major just running a little rich with, in my opinion, too high of an idle. The truck isn't hard to start at all and runs great minus the richness. I plan on going from Bay Area to Tahoe. Do you think I will have any...

Ok so my 40 is just being terrible. I parked it for a while then decided to do a tune up. So new plugs, points, rotor, plug wires, new "toyota oem" carb from eBay, new air filter... Now when I try to start my 40 it runs then hammers it and then stalls every time! I have tried filling the fuel...

I'm looking for a stock carburator for my 5/1977 FJ40 (federal with emissions/smog in place). I believe I need an Aisan 21100-61023. I do have a question. What is the difference between the two: Aisan 21100-61024 (believe fits years late 1977 thru 1978) and Aisan 21100-61023 (believe...

Hey there, new to the fj40 club. Just bought a 71 fj40 FULLY STOCK over a month ago. Heres the condition of it when i got it: Imgur: The most awesome images on the Internet Well, this was it after a few modifications.. First, the front rear and back left drums and the master cylinder were...

I'm on a 6,000 mile trip in the FJ60 and have a few maintenance items I'd like to take care of near Santa Cruz if there is a shop in or around town (or a home shop with one of you guys would be even better). Items to address include: -carb adjustment (was tuned for 9,000 ft and will be mostly...

I am trying to get my 79 FJ40 running i have had it for about 15 years and this year i finally started to work on it to restore it. I was able to fire it up and drive it into the garage (3 months ago) when i did this i noticed gas spitting out of my fuel pump. So i just got around to replacing...

Good morning everyone! Forgive me if this is mentioned somewhere, I sure as hell can't find it if it is. lol My FJ60 air handler just sits atop the carb. Shouldn't there be a seal of some sort there? I can't seem to find anything related to it. Any insight? Thanks!

post up the ones you find and the ones that might work on a cruiser. mine is an old school K&N that i converted to stud/nut instead of clips

I am new to the forum and new to the Landcruiser owner club. I recently bought an 87 fj60 with a leaking headgasket. After sending the head off to be rebuilt, I found out that it is cracked. This has caused me to shift the direction of the build completely. I know that the protocol is to...

Background: 1977 2F desmogged with a Webber 38/38 (all PO work) My goal is to go back to all OEM Aisin. I’m been searching and haven’t found much guidance on going back to OEM (feel free to link me as my search-foo isn’t the greatest). I have a 1977 Carb on the shelf, but it needs a rebuild...

Hey guys, been a long time lurker for this site. I've finally decided I need to make my own account and ask for some more specific help with this issue I've been having with my truck. Hoping someone out there can help me out. From what I can tell there's something wrong with my carburetor...

We are trying to locate a couple replacement parts for our 1972 FJ40 as part of our carburetor rebuild. 1. We damaged the "discharge weight stopper" while removing it. 2. The "screen" was apparently missing. We have found the parts here but they are not available: Search by Part Number 042-27...

My son and I are working on this 1972 FJ40 for him. We are both rather new to doing any serious type of automotive work but we are learning and having fun doing it. We are hoping we haven't bitten off more than we can chew. :-) Currently we are rebuilding the carburetor using some nice...

$325 includes shipping I have a rebuilt carburetor from Specter Off Road that came with my 1975 Fj40. (I had a different one put on.) Model 042-01I-R Never installed still in box that Spector used. Their price is $425. Shipping to lower 48 included. I am located in the Western suburbs of...