alignment

Has anyone noticed and/or addressed a torque steer issue on their 200? I recently had my 200 lifted with the OME/SPC UCA Kit by the fine folks at Slee Offroad, didn't visually notice that the rear axle had moved one way or another, alignment was done at their shop (specs look great on paper)...

Doing a new short block and cylinder head overhaul on my 96 LC, think I have all the gaskets, then realized there are a lot of alignment pins, I noticed the head and "1 oil pan, tranny and rear crank oil seal retainer and timing chain cover pins. Are there others I missed and any other little...

So after finishing up my slight lift (2" springs in the rear & a torsion bar reindex/crank) I took it to the Toyota dealership to get it aligned today. After a few minutes on the lift I get word from the mechanic that he will not be able to accurately adjust my camber and caster. I will try to...

I'm having some alignment issues following my OME install. The truck still pulls to the right even after an alignment. It's not terrible but it's definitely noticeable at highway speeds. If I take my hands off the wheel, I'll be in the next lane within a second or two. I took it back to the shop...

I just got my truck back from TJ performance in Orange. Had OME 865s / Torsions / diff drop / Slee Ucas / Fox 2.0s. Truck rides Amazing much better than stock. However their idea of level differs from mine. They had the torsions cranked so high there was 15mm of down travel. Before After...

Had to replace ac compressor. Now it seems that the other belts aren't aligning well.

So I have been battling an issue with steering wheel feedback almost the whole life of my ownership. It was even noticeable at stock height. I have almost completely remedied the situation by replacing sway bar bushings, r&r'd the AHC suspension, and this previous weekend replacing the rack &...

I have a 1978 FJ40. I replaced the stock seats with the Corbeau Sport Seat, Corbeau seat bracket and stock mounts. I am having some issues with the alignment. I used washers to shim everything level at the back of the seat but I am not happy with the results. I feel like the seat brackets...

So I installed the 2" Ironman lift and took it in for an alignment to find out my wheel bearings were bad and I needed new inner tie rods. I replaced the tie rods and repacked the bearings as they were in good condition. Took it back for an alignment and here is where I am. Theguu that did it...

I may need a little rth today which is now Monday the 23rd. I am traveling and need an alignment ASAP. I am in El Segundo, California tonight and have to hit Anaheim tomorrow at some point before 5pm before I enter Baja early Tuesday morning. I just spent the last four days in my friends shop...

My 2004 GX has a terrible ride, and since I've already replaced most of the suspension (rear shocks and air springs; front shocks and mounts; front sway bar links; lower control arm bushings) and had no improvement, I am thinking maybe it's the alignment that's the problem? Would really like to...

Hi this is my first real post on this forum and I hope I can find the answer to my question. I was wondering if I could get some advice. I'm about to buy a new to me 2000 Lexus Lx470. It has a few problems nothing to be too concerned about. My main worry is when test driving it I had to hold the...

So, I've searched high and low and couldnt find any threads addressing a similar mystery- hoping you guys can give me an idea. I have a 99 LC with complete 2.5" OME kit, diff drop and SPC UCA's on 285.7516 BFG's. Did the suspension over a weekend with a friend taking our time. Once we...

I did some searching on Google and here, but couldn't find any definitive information. Does anybody have the specs for alignment of an '88 BJ70? Everything is bone stock, other than the tires, which are 175/65R15.

Hey gang....Just installed an entire new SOR Heavy Duty Suspension 3" Lift Kit on my 85 Fj60. I added the Skid plates, they seem pretty burly..hope that they do well. Read some old reviews about it after the fact..so if they suck, I am gonna change to the Bolt flip kit from 4+plus. Cleaned...