60

I reckon we should have a competition for the most difficult job on a 60, because its a 60 (not talking cracking a thermostat bolt). My vote is to install the AC Idle Pully Nuts (or even adjust the thing). Aus series 3F. I wanted to tighten the AC belt as it was squeaking, and stupidly turned...

Figured I’d throw these up here in case someone wants to move a shackle mount, undo a shackle reversal or upgrade their 40 to larger 60 bushings… Full set of 60 spring and shackle hangers cut cleanly off the frame $150 for all plus shipping Or $75 for each end

I decided to start a new thread since I am finally done and have completed the final prototype. 12 gauge CR steel. I can build this in different air flow designs also. This kit is available now for preorder at $1250.

Hi everyone, Long time lurker and poster on Mud, but normally in the 70 Series section (and some ownership of 80's and 100's), but never a 60. Well, that has just changed, and I am the proud new owner of a 1988 HJ61, 12HT mated to a manual box. I'm very lucky, it's been with it's owner for 26...

Dana point Ca ready to drive whenever I need. Thanks all!

I’m building a disc brake axle for my 45. I’m piecing together 60 knuckles onto an axle tube from a ‘74 55. I had to grind the inside of the axle tube for the birfields to fit. All that’s done and I’m assembling the knuckles out. I discovered that when I install the hubs that there is no...

Have an 86 60 series---i've read and noticed some of you have front seats from BMW or other rigs--I'm looking for leather, heated front seats and a matching back seat that folds down. I'm thinking of possibly 4Runner or 80 series seats but haven't seen anyone do that here so guessing they don't...

I'll do all posts with pictures. When sold, that ad will be erased. All prices are plus shipping via USPS. 16333-61110 2F Thermostat Housing that fits FJ60 or 8/'80+ FJ40. $175

As title states, looking for a slimline for an fj60. Located in Ogden area, willing to travel within reason. Bonus points for wind deflector and mounts.

Description: Flywheel Housing Bottom Cover along with its gasket 04317-60020 P/N: 31104-60020 Condition: NOS ( New old Stock genuine part in excellent condition , only have minor storage scratches as shown at the attached pictures). Fitment: Fit on 4 & 5 speed Fitment pictures attached...

I was starting to highjack CND's thread with the LC200, so here's a new one. Kind of a continuation from my winching with Lithium thread, which concludes that winching with Lithium is somewhat new territory. At least when I set up my winch wiring, I made the leads long enough to reach both my...

Wrapping up the design and manufacturing details on the ORIKAWA 60 Series Center Console this month. To maintain a reasonable price-point the initial run (at least) of consoles will be done as a batch. Pre-Order will open in the next two weeks with units expecting to ship in October. Final...

Wrapping up the design and manufacturing details on the ORIKAWA 60 Series Center Console this month. To maintain a reasonable price-point the initial run (at least) of consoles will be done as a batch. Pre-Order will open in the next two weeks with units expecting to ship in October. Final...

I apologize if this information has already been discussed, but I was unable to find my combination of questions. I have a 10/85 FJ60 with a Holley Sniper. Currently I am running the frame rail pump, but am in need of more fuel capacity on many trips. Jerry cans aren't especially practical with...

Fj60 arb bull bar wanted. Near Austin or in Texas preferably. Preferably used.

I have a dana 60 rear that fits in a fj 40. 410 gears, lash gears and bearings look good. Not sure of the brakes they look like fj 60 breaks they are also good. I was saving it for a hot rod but changed my mind $500 . I will put on a pallet if you arrange shipping .... Colorado springs

I have a master cylinder/booster with a brake proportioning valve as per the first picture in this thread. If you have a 1987-89 non-US 60 series with front disc brakes and no rear load-sensing proportioning valve, could you please tell me which output from the proportioning valve goes to the...

Going to start off by saying I’m terrible at build threads and usually end up not completing or updating them. Just so everyone is aware.. Short recap on my 60. I found it about 30 minutes north of my house. The engine was torn apart, and had been sitting for 20 years without the head on. Most...

Hi Gents, been a long time quiet reader for several years and want to introduce myself with this post. I have been collecting and restoring several historic Cruisers over the last 15 years, but had my focus on mainly 60 series. Have got a V8 79 series as a company vehicle and 2 HJ61 as a...

Is this any of you guys? If so we’re neighbors