3fe

Hey everyone, so I'm looking for anyones recommendations based on experience with a 3FE. Here's the situation: 92 FJ80, 3FE, engine seized, I got a replacement and it's been rebuilt by a shop, installed by another shop. Pressure test when cold is good, but once it heats up, it starts dumping...

I got a 3FE head I bought but decided not to use, it looks like it was damaged but was fixed, it was run with the damage for 5000 miles. I also got the 3FE intake Also if you're interested have a cam and crank from the 3FE, timing cover, pistons, rods, etc. Willing to ship as long as buyer pays

Pulled this powertrain out of my personal FJ80 to do an LS swap. I have the full engine, emissions equipment, air box and meter, ECU, and all accessories. Price includes the A440 trans with ECU and tcase however I will need parts of the harness to facilitate the LS installation. The engine...

Hello fellow cruiser owners, I have a dumb question. Looked around and have found conflicting answers on what shorting the TE1 and E1 terminals on the 3FE diagnostic plug actually does in terms of ignition timing/ECU. When setting ignition timing, does shorting the terminals just stop the ECU...

Southern California noob here with a 1991 Land Cruiser 3FE. 202k Miles, Old Man Emu Suspension, Methods on 33 1/2 Goodyears. I’ve already been combing through the site, wealth of info and thanks to those that are active. Will be searching for top things noobs should do with their new LC and the...

Decided to hurt my resale value and do an LS swap. :rofl: In Lawrenceville GA. Would prefer local pickup. $1500 obo Current mileage is 329114 Engine is in good running condition. The alternator will need to be replaced. The engine has not been overheated but if it is pushed hard on extended...

I have a 3FE fan shroud from a 91 80 series that is left over after my motor swap. The tabs are all in good shape, nothing broken or cracked. Asking $40.00 plus shipping. Located in New Mexico.

I have two (2) sets of brand new Toyota intake boots for the 3FE 80 series. I originally ordered them from a well known west coast parts supplier but they showed up WAY late, so by the time I finally received them I had already installed a set from some where ells. I'm also not sure why I got...

Selling my 92, I've owned it for 12 years and just don't have time for it lately. The tires need replacing badly, the tread is OK but they are old and one is worn on the edge unevenly. I do drive this once a week, mostly to keep the battery up, but lately I've been staying under 30 mph while...

31230-36161 replaces 31230-36160. Please double check part number to make sure it will meet your application. $60+ship

Who can tell me which one is correct Both pictures are from same manual one shows Yellow and blue white on the #1 pin of the injector connector the other picture shows it on #2 pin On my cruiser I have bank 1 1-3 on pin #2 and bank 2 4-6 on pin #1 I verified by checking continuity fron...

Hi All I’ve been wanting to go Fuel injection for a while but I have a few questions 1 Will a 3FE intake etc bolt directly on the 3F I have a aftermarket management system so I’m good with that 2 in South Africa there is not allot of places to get 3f parts where can I start looking Kind...

Alright, I need some help with my 3FE. Its smoking white sweet smoke really badly. Ill start with a story for context. Wife and I drove her 80 series out to Sequim WA from Tacoma WA, about 117 miles one way. It was our first long drive in the Cruiser. Id finally finished my list of tune up and...

Looking for a good condition upper thermostat housing for my 3FE. Have a new lower housing and the upper is beyond help. Shipping to 49459.

I have two intake manifolds Two heads, one in good working shape other needs seats cut Wire harness and computer and all injectors, distributor's Alternator two oil coolers valve covers push rods and rocker assembly, no lifters cant ship the heads but everything else I can. also have a good...

I was working out my vacuum hoses and trying to put everything in the right places, since the cruiser ran like crap. Found a hose missing off the 3 from the intake and then the egr was missing a hose. I got everything lined up and then this part appeared behind my air.....barrel? Question...

Had to be done

** I HAVE PILES OF 80 / LX450 PARTS JUST ASK ** It's been a long time since I started a new part out thread. I've sold many, many, many parts 93-97 but now adding 91-92 & LX450 to the mix. Please message me with specifics of what you're looking for. I do ship SMALL parts.....but large items...

I have a running 3FE engine and transmission 242k miles, no smoke and transmission worked great. Out of my 91, (doing an LS Swap) mostly complete, no electrical harness and missing some sensors. free for pickup in Marysville, WA.

Ceramic coated , planed/machined ready to install 3FE exhaust manifolds ready to install $500. Shipped to lower 48. Note: EGR port has been welded shut and shield bosses have been removed. I was going to use these on a 2F but couldn't get machine shop to thin the flange to match up with 2F...