3f

I currently have a 1988 fj62 and the trans is completely toast on it and I have an option to get a fj70 series 5 speed manual as long as i pay just the shipping for it. Has anyone swapped a 5 speed h150f behind a 1hz diesel in a 62 with a 3f motor? I'm guessing it wont be a bolt on project but...

Doing a frame off restoration of my father's 65 FJ40. Looking to build a 2F-E for it. Need complete 2F engine, 3F-E cylinder head and all engine management components - intake and exhaust manifolds, wiring harnesses, etc. I live in GA, but the vehicle is at my parents' house in WA...

I am pulling the 3FE from my '89 FJ62. It is all original as much as I can tell. It does have some leaks. 310K original miles, again as far as I can tell. Trans was rebuilt by PO and has ~1,500 miles on it. Comes with ECU, harness etc up to the transfer case. That is staying with the new motor...

I have been using the Weber 38 DGMS on my FJ80 3F engine and works just fine. I live in Bogota, Colombia, meaning +5K feet above sea level, but I have been wondering if the carburator really makes a significant difference on my rig considering it has headers. Also carries 35¨ tires and stock...

G'day guys can anyone shed some light on which option is best Iv had a 3f built for a turbo but the guy I bought the turbo gear off has ripped me off now I'm up for options. What's your thorts

Hey guys, new to IH8MUD. Racking my brain trying to figure this one out. Runs fine however when accelerating at around 2000rpm feels like bogging down/spitting/sputtering. I've changed all spark plugs, inspected leads, new fuel pump, just today did a carby rebuild. At each of these stages ive...

Hi everyone,I've been lurking for quite some time now and finally decided to join officially:smokin: Just some basics,I live in South Africa, I'm 21 years old,good mechanical knowledge and always ready to learn so I apologise in ahead for any stupid questions. I enjoy the outdoors and 4x4ing...

Looking for a 3F for an 89' , in washington state, pm!

I won't be needing this anymore. $75 plus shipping.

I have a spare gearbox for a 1fz engine which is the H151f. My friend is looking to swap out his 4 speed gearbox which he has on a 3f engine. I was wondering if they were the same gearbox or similar and could work.

Hello, I am new to the forum so for give me if I am doing everything correctly. But i own a 1971 FJ40 that I bought for $500 two years ago (as you can imagine it looks rough. The the vehicle had been sitting since the early 80s and I am currently in the process of "restoring" it. The body has...

Hey, so some of you have been following my posting on building up my 87 fj60. Last night as I was prepping the frame for the repair I noticed something that raised some red flags (and maybe it's not a problem.). The engine says 2F on the valve cover but the bellhousing has 3F stamped on it. I...

I need a head for a 3F engine. Would love to know if anyone has one state side.

Morning, mud! I figured it was time to start one of these, but it'll definitely be a slow-go as there's a lot going on for me right now. I found my '91 FJ80 roughly a year and a half ago. Long story short, my boss got the short end of the stick in a deal with a used car salesman and ended up...

I'm rebuilding a 3F motor and in the process bought a "full" gasket set believing all gaskets needed would be included. It does not have whatever it is that seals the two halves of the exhaust gasket together. In my limited experience of engines I have never seen a setup like this. Local parts...

I'm rebuilding a 3F motor and in the process bought a "full" gasket set believing all gaskets needed would be included. It does not have whatever it is that seals the two halves of the exhaust gasket together. In my limited experience of engines I have never seen a setup like this. Local parts...

I have both option to use on a new FJ45 restoration. But cant find a simple answer on the exact difference in terms of performance. As far as I have been able to read, there is no significant difference! Is this correct?

I have been trying to trouble shoot a no spark issue for days on my 91 LC. I have tested 3 coils, replaced the points with a pertronix system that works in another LC I own and still I have no spark. I have read and re-read the manual I have and studied the wiring diagram as best I can; I am at...

So I discovered a bit of a problem developing with how the car is idling, it gets stuck at around 1.5-2k revs. It doesn't happen all the time, and when it does I can usually unstick it by tapping the accelerator in neutral, but then the revs drop so low (400 or less) that sometimes the car...

Are any 3F engine parts compatible with the 3FE? What about FJ62 interior stuff, like blower resistors? Does any of that work with a FJ80?