1fz-fe

I have a 1994 1fz fe 1994. Can anyone tell me the diff between 1994 and the 1995? I want to put a maguson supercharger but the kit is only for the 1995. Can someone tell me the diff with the 1995 and 1994?

Recently over the past month and half my 96' started very quiet knock that grabbed my attention this past week as it got noticeably louder. I've been learning my way around vehicles as I work on this thing so my knowledge is limited. The engine is believed to have 130,000 miles, so still pretty...

I have an engine and transmission from a 1996 Toyota Land Cruiser, same as Lexus LX450. Engine had 230k miles when removed from wrecked cruiser for a project. Engine was running when pulled. Asking $1000 obo. Engine and trans together Willing to split and sell separately as well Engine...

Hey Mud! I will be tackling the dreaded p0401 code per the FSM and this awesome post. While in there I figured I might as well pull the fuel injectors and send them off for cleaning. They have ~180k on them. My question is...what are the part numbers for all the o-rings / grommets / insulators /...

Hey Guys, I'm having an issue with my throttle position sensor, if I have it connected, the engine wont rev past about 2200rpm, whereas if I pull the plug, it is happy to rev as far as i push it. I've checked wiring, done continuity tests on the wires ect. I'm also getting engine fault codes...

Hello! I'm looking to purchase a low-to-mid mile complete engine to swap into my 94 FZJ80. I'm looking for motors that run in good condition, not looking to do any bottom end work. shoot me a pm or reply to this ad, thank you. PS: I am located in Salem Oregon, I can travel moderate...

Anyone have or know of a FSM for the 98+ FZ with the coil packs and redesigned head?

As A Toyota Lover Had Done A 70 Series Project Recently & Jumped to 80 Series ... A Bone Stock FZj80 In My Garage Was Welcomed Recently ... Em kinda Person Who Like To BUILD Machines With Heart & Keep Them Like My Home Members ... Enough Writing :p Lets Introduce U To My RIG " The Devils "...

Just finishing up an LS swap in a 94 FZJ80 and we have the comeplete driveline forsale, minus the t-case and driveshafts! The motor and tranny are in perfect condition and only have 73k orginal miles! Everything is complete intake, starter, alternator, etc.... $2000 Shoot me a message for...

Los Angeles area Toyota Land Cruiser 1FZE engine, still in the car now and running strong. No noises, or overheating, idles smooth, runs strong, good oil pressure, lots of power. 283,000 miles on it. $1300. I can drive it to your mechanic to have it checked before you buy it, and they can...

Hi Guys, just wondering if the rotor on the distributor should be at TDC when the two alignment marks on the end are aligned..

Hi All My 93 LC80 1FZ-FE is bogging and jerking unpredictably. Sudden drop in RPM then picking again. Sometimes it doesnt go above 2500 RPM on full throttle. It picks up again and would drive normally up to 4200RPM. then it would do it gain. This started when I passed by a very small poodle...

I have a 1995 1fz-fe for sale for $800. It has 232,xxx miles. Its a 95 block and head with a 94 upper and lower oil pan as I put the 95 oil pans on the new engine. It's located in Bailey Colorado. It runs great. Was going to change head gasket and front and rear main and ended up finding a real...

For a while my land cruiser's transmission has been acting up. It won't shift into reverse or 3rd gear until it gets warm, the reverse dash light does not come till it gets warm either even after it does it still slips for a quarter of a second till it finally goes into Reverse or 3rd but then...

Quite a while ago I stumbled across a sensor hanging by the wire in my engine bay, after a quick search on the web I realised it was a Door position sensor so i unplugged it and stored it in the car for a while so i'd have one less thing dangling in my engine bay . Today I decided to research...

Good afternoon, Can anyone please advice if an intake manifold from a "newer" version of the 1FZFE engine would work in the U.S. Version ( used in a 97 LC) without major modifications? I see this " newer" version doesn't have EGR system. I found the piece for a good price, I am interested to...

From a good running Cruiser. 180,000 miles. Head was pulled from motor to do gasket and valve job, but wound up being used on a different cruiser. $500. I have an engine hoist here to load it in your trailer, truck or wheelbarrow. Complete with oil pan, flywheel, crank pulley, timing gear...

I began detailing the rebuild of the 1FZ-FE in my truck build thread (listed in my signature), but it soon began to dominate the thread, so I decided to create a dedicated thread. My '97 Landcruiser died early and suddenly, with only 175k on the clock, when a misplaced bolt got into the timing...

Hey guys and gals, I'm hoping someone may have a good rebuild or low mileage 1FZ laying around sometime soon. My '94 with 208K is making a lovely lower end knock that comes on nice and noticeablely every time I get on the gas or torque load increases. As much as I'd like to pull the engine...

Since starting Wits' End last May, the number one thing I keep getting asked to make (other than the battery disconnect, the D-Pillar mount, the second row bug screens, etc etc) is the York bracket and pulley kit. For those of you that have been around long enough you'll remember that I did the...