1fz-fe

Hello there, Can someone please indicate if any of the following pistons will work if installed in my 80s 1FZ-FE? Pn 13101-66050-02 Pn 13101-66040-01 Pn 13103-66020 Pn 13105-66021 I look forward to your reply, Thanks in advance,

After pulling the motor, I found the TC stem/alignment nipple jammed inside the crank at an odd angle. I also have a little damage to the side of the spacer, almost looks like someone took a grinder to it. The stem from the TC has an odd warp or bend to it. I don't really want to replace the...

I have pulled my 1FZ-FE and A343F as I am in the middle of a diesel conversion. The motor ran great when pulled. There are 180k miles on the engine. Let me know what you want, I am located in Chester, NJ 07930, but will ship if needed. Parts already sold: Distributor ECU MAF

SoCal for 91 to 97 Easily shipped by mail. Paypal OK Prices do not include shipping. Shipping $6 to $12 for as much as I can stuff into a flat rate small mailer or envelope. Outer Seat Belts: Front Row Seatbelts Grey $35 each Second Row Seatbelts Grey $25 Second Row Seatbelts Brown $25...

I just pulled the trigger on a full rebuild and super charger install from slee in golden colorado on March 17th. Im getting a new shortblock from toyota and having the top remaned. so im trying to figure out what all to sell, be it just the short block or sell the long block as a whole thing...

~~~~~~~~~~~~~~ S O L D ~~~~~~~~~~~~~~~~ I have a brand new, never used Performance MAF Housing by Landtank from AJIK Overland Exchange. This unit is brand new. Write up from webpage Performance MAF Housing | Toyota 80 Series Land Cruiser and Overland Gear. Short Description Gen IIl...

Another one! Just like the last one I sold. FJ80 Factory Tool Kit and Bag: (from a 1995) 2 Toyota Open End Wrenches, pliars, lug wrench, spark plug tool, hubcap spoon, jack driver, crank handle and extensions, and the tool bag. Tool bag, pliars and wrenches are factory stamped "Toyota" and...

I thought the culprit was leaky flange gaskets. After getting those replaced, the sound is still there. Any ideas? It's in a 1996 LC80 with 184k miles. > Thanks!

I have an 80 series with the 1FZ-FE engine with 320,000kms, and having just completed a full engine rebuild, I have discovered that the wiring and connectors have deteriorated significantly, with some falling apart trying to reinstall. I am just looking at what my best option is to fix this, do...

So three years ago I replaced the head gasket on my '97 and got the head surfaced and cleaned and even had a valve job done. put it all back together following the FSM instructions and this past weekend I was driving and noticed the temp gauge a 1/4 inch above where it normally is. So i pull...

I think I have this diagnosed but I thought Id run it by you guys first. Headed to work the other morning, up hill with a pretty good head of steam, around 50 mph when the truck wouldn't shift to the next gear. I pulled over and the engine ran very rough and died. Started right up and pulled...

Hi, I am currently rebuilding my 1FZFE and want to use an MLS head gasket. Any issues with using Torque to Yield Head Bolts? Or should I only use ARP studs? Thanks

Manik Side Steps for FJ80/80-series For Sale Reason for Sale: I replaced them with rock sliders Condition: Fair - could use some TLC (pun intended). The bars are structurally sound. Needs a wipe down, maybe rust remover in some spots (How to Remove Rust from Metal), maybe a coat of spray paint...

Hi, have just rebuild my 1FZFE and am having an issue with the idle. It runs okay for a few seconds after cranking, then idle shoots up to 3200, then drops to 2200 and continues going up and down for a few minutes until it just has enough and cuts out. Have checked the spark plugs, ignition...

1FZ-FE , 231,524 miles 1994 $750.00 Trans and T-case also available PO states that the truck ran early in 2015 and was parked, would not start in 12/15 PM if interested

Yet another 1FZ-FE rebuild thread... hope there are a few things in here that may help someone down the road. First I want to say thanks to all of you who took time to answer my questions along the way and to those who have posted in the past. This forum is nothing short of incredible. What I...

Los Angeles area LOOKS GREAT AS AN UPGRADE if yours doesn't have it. Includes inside moldings that enclose the light and everything that goes with it. This is factory from a 1994, complete, and will be sent to you freshly removed from my tailgate hatch. $45 + shipping. Can be installed on all...

SoCal Running car had only 180,000 miles on it. Head Gasket went two months ago. car is being parted out. Prices do not include shipping. Alternator $65 Bench tested to be sure it is in good shape and it is. Fan $35 Fan Clutch (aftermarket) $25 Fan Shroud $45 Radiator is sold.

SoCal. Prices do not include shipping. Paypal OK Does NOT fit 3FE engine. All these parts are from a good running 94 that lost it's head gasket. Distributor with cap $85 Plug Wire set Smog Valves, etc. Please send me a picture of what you are looking for to Deathvalleypaul@yahoo.com OR...

SoCal Xlnt condition - NO cracks or damage. Paypal ok. Shipping $5.95 priority mail Fits ONLY on driver side front or driver side rear door, Same part used 91-97